FiberHome AN5506-04-F2 Router Manual PDF (Setup & Configuration Guide)

Page 26 / 38 Scroll up to view Page 21 - 25

AN5506-04-A GPON Optical Network Unit User Manual

2-4

Version: A

Table 2-2

Interfaces and buttons of the AN5506-04-A

Interface or

Button

Meaning

Type

Description

Power switch

Button

Switch on/off the power.

Reset

Reset button

Button

Press the button and then

release to restore factory default

settings.

Power

Power interface

Power

interface of

double pin

For connecting DC power

adapter of two pin.

PON

Optical

interface

SC/PC

For connecting the ODN.

Console

Network

interface for

local debugging

RJ-45

For local device debugging. Not

open to subscribers.

LAN1/2/3/4

Ethernet

interface

RJ-45

For connectiong PC, router and

so on.

Page 27 / 38

Version: A

3-1

3

Product Installation

3.1

Preparation Before Installation

3.1.1

Unpacking Check

After opening the packing case of the AN5506-04-A, please check

articles in the packing case according to the packing List. If the items do

not match the packing list, contact the local office of FiberHome directly.

3.1.2

Installation Precautions

Before installing the AN5506-04-A please ensure that the following

requirements are met:



There are waterproof, moistureproof and lightningproof conditions

at the installation position.



The installation position can provide conditions for the AN5506-04-A

to connect with the exterior. For example, there should be suitable

outlet space for power supply cable and network cable.

Page 28 / 38

AN5506-04-A GPON Optical Network Unit User Manual

3-2

Version: A



The installation position should be able to ensure enough air flow,

convenient for cooling of the equipment.

3.2

Placing the Device

You can place the AN5506-04-A on the stable plane, such as an office

desk. The placing methods are as follows.



Take out the AN5506-04-A from the packing case. Before delivery,

four rubber pads are pasted to four corners on the bottom of the

device.



Place the AN5506-04-A on a stable desk slightly and ensure the

ventilation on both right and left sides.

3.3

Cable Connection

3.3.1

Connection of Network Cable

The AN5506-04-A Ethernet interfaces can connect subscriber terminals

such as PCs and switches through network cables. Follow these steps to

connect the network cable.



Plan the wiring and cabling mode of the network cable, measure the

distance between the AN5506-04-A LAN interface and the

subscriber terminal, and select the network cable with a suitable

length.

Page 29 / 38

3

Product Installation

Version: A

3-3



Fix the network cable and then make Ethernet connectors for both

ends.



Connect Ethernet connector of one end to a certain AN5506-04-A

LAN interface.



Connect Ethernet connector of the other end to an Ethernet

interface on a PC or a switch.



The connection of the network cable is finished.



Note 1: Transmission distance of the network cable is less

than 100m. Therefore the length of the network cable

prepared by the subscriber should not exceed 100m.



Note 2: The

AN5506-04-A Ethernet interface supports

MDI/MDIX self-adaption. Either straight-through network cable

or cross-over network cable is suitable for cabling.

3.3.2

Connection of Optical Fiber

The AN5506-04-A adopts wavelength division multiplexing (WDM) mode

and provides “triple-play” integrated access. The connection steps of

optical fibers are as follows.



Plan the wires and cables layout mode of the optical fiber; measure

the distance between the AN5506-04-A PON interface and

upstream optical splitter; select the optical jumper with suitable

length.



Fix the optical fiber; remove the protection covers of the optical

jumper and the AN5506-04-A optical interface.

Page 30 / 38

AN5506-04-A GPON Optical Network Unit User Manual

3-4

Version: A



Insert one end of the optical jumper into the AN5506-04-A PON

interface slightly.



Connect the other end of the optical jumper with the optical splitter.



The connection of optical fibers is finished.



Caution 1: If the optical fiber jumpers are not used, make sure

optical fiber jumpers and the AN5506-04-A optical interfaces

are

covered

to

avoid

dust

contamination

and

water

penetration, which lead to the uselessness of optical fiber

jumpers and the AN5506-04-A optical interfaces.



Caution 2: Connect optical fibers at last if possible. Lay

optical fibers at the position without extrusion.

3.3.3

Connection of Power Cable

The AN5506-04-A adopts the power adapter with two pins, the

connection steps are as follows.



Take out the accompanied DC power adapter with two pins.



Connect one end of the adapter to the power interface of the

AN5506-04-A.



Connect the other end to AC socket.



The connection of power cable is finished.

Rate

Popular FiberHome Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share