1. Home
    2. /
  2. Manuals
    3. /
  3. Engenius
    4. /
  4. ESR-9750G
    5. /
  5. 19
Page 91 / 94 Scroll up to view Page 86 - 90
91
- Back-up
The page allows you to save (Backup) the router’s current configuration
settings. When you save the configuration setting (Backup) you can re-load the
saved configuration into the router through the
Restore selection
. If extreme
problems occur you can use the
Restore to Factory Defaults
selection, this will
set all configurations to its original default settings (e.g. when you first purchased
the router).
Backup Settings:
This can save the Broadband router current configuration to a
file named "
config.bin
" on your PC. You can also use the
<Upload>
button to restore the saved configuration to the
Broadband router. Alternatively, you can use the "
Restore to
Factory Defaults
" to force the Broadband router to perform
a power reset and restore the original factory settings.
Downloaded from
www.Manualslib.com
manuals search engine
Page 92 / 94
92
- Reset
You can reset the broadband router when system stops responding correctly
or stop functions.
Downloaded from
www.Manualslib.com
manuals search engine
Page 93 / 94
93
Appendix A – FCC Interference Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
²
Reorient or relocate the receiving antenna.
²
Increase the separation between the equipment and receiver.
²
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
²
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Downloaded from
www.Manualslib.com
manuals search engine
Page 94 / 94
94
Appendix B – IC Interference Statement
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This device has been designed to operate with an antenna having a maximum gain of 2 dBi. Antenna
having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna
impedance is 50 ohms.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Popular Engenius Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top