Page 121 / 135
Scroll up to view Page 116 - 120
121
Bandwidth Allocation
Set network resource usage, for inbound and outbound traffic, based on local IP and port ranges.
Type
Select Download or Upload to specific the direction of packet
traffic.
Local IP Range
Enter the local IP range of the current configuration.
Protocol
Select the protocol to manage for the current configuration.
Port Range
Enter the local port range of the current configuration.
Policy
Select Min or Max to specify the type of configuration policy.
Rate (bps)
Select the bandwidth rate, in bits per second (bps), of the current configuration.
Click
Add
to save the settings and list the configuration in the
Current QoS table or
Reset
the discard changes.
Click
Apply
to save the settings or
Cancel
to discard changes.
Page 122 / 135
122
Routing Setup
Typically static routing does not need to be setup because the router has adequate routing information after it has been configured
for Internet access. Static routing is only necessary if the router is connected to network under a different subnets.
To view the Routing settings, click
Advanced
then select
Routing
.
Note:
To enable a static routing, NAT must be disabled.
If the router is connected with a network under the different
subnet, the routing setup allows the network connection within
two different subnets.
Enable Static Routing
Click Enable Static Routing to activate the feature.
Destination LAN IP
Enter the LAN IP address of the destination device.
Subnet Mask
Enter the Subnet Mask of the destination device.
Default Gateway
Enter the default gateway IP address for the destination device.
Hops
Enter the maximum number of hops within the static routing
that a packet is allowed to travel.
Interface
Select LAN or WAN as the interface.
Click
Add
to save the settings and list the configuration in the
Current Static Routing table or
Reset
the discard changes.
View and select devices in the Current Static Routing Table.
Click
Delete Selected
or
Delete All
to remove devices
from the table. Click
Reset
to stop.
Click
Apply
to save the settings or
Cancel
to discard changes.
Page 123 / 135
123
Wake on LAN Setup
Wake on LAN setup (WOL) allows the administrator to activate a computer over the network.
To view the WOL settings, click
Advanced
then select
WOL
.
Enabling WOL over WAN
Click
Enable WOL over WAN
to activate the feature.
Server Port
Enter the server port of the device to activate.
Wake MAC Address
Enter the MAC address of the device to activate.
Click
Start
to activate the device.
Click
Apply
to save the settings or
Cancel
to discard changes.
Page 124 / 135
124
Tools Setup
Configuring the Administrator Account
Change the router’s system password as well as setup a device
to remotely configure the settings.
To view the Admin settings, click
Tools
then select
Admin
.
• Login Name:
Keep or change existing login name
•
Old Password:
Enter the existing administrator password
•
New Password:
Enter the new administrator password
•
Repeat New Password:
Re-type the new administrator password
•
Graphical Authentication:
To enable or disable CAPTCHA
Remote Management
•
Host Address:
Enter the designated host IP Address.
•
Port:
Enter the port number (Default:
8080
) for remote accessing
management web interface.
•
Enable:
Select to enable remote management.
Click
Apply
to save the settings or
Cancel
to discard changes.
Note:
To access the settings of the ESR Series Router remotely,
enter the router’s WAN IP address and port number.
Page 125 / 135
125
System Time Setting
Change the system time of the ESR Series Router and setup automatic updates through a network time (NTP) protocol server or
through a computer.
To view the Time settings, click
Tools
then select
Time
.
Synchronizing with an NTP Server
Time Setup
Select how the ESR Series Router obtains
the current time.
Time Zone
Select the time zone for the ESR Series Router.
NTP Time Server
Enter the domain name or IP address of an NTP server.
Enabling Daylight Savings
Click to enable or disable daylight savings time.
Start Time
Select the date and time when daylight savings time starts.
End Time
Select the date and time when daylight savings time ends.
Click
Apply
to save the settings or
Cancel
to discard changes.
19216811.live