Page 6 / 97 Scroll up to view Page 1 - 5
1
1 Introduction
The AR-7284WnA supports AnnexA mode. It provides four
10/100 base-T Ethernet ports for user. The device provides
high-speed ADSL2+ broadband connection to the Internet or
Intranet for high-end users, such as net bars and office users.
It provides high performance access to the Internet,
downstream up to 24 Mbps and upstream up to 1 Mbps.
The device supports WLAN access to the Internet, such as
WLAN AP or WLAN device. It complies with IEEE 802.11b/g,
IEEE 802.11n specifications, WEP, WPA, and WPA2 security
specifications.
You can configure the router by running the Setup Wizard in the
CD-ROM provided in the package. The wizard provides quick
setup
for
Internet
connection,
Ethernet
WAN
Internet
connection, SSID, wireless security, firmware upgrade and
changing router’s password. When you start the Setup Wizard,
you will get the following Welcome screen. Please choose the
language to start with and follow the easy steps in the Wizard.
No instruction for the Setup Wizard is given here.
If you lost the CD-ROM or you prefer the traditional web setup,
please follow the procedures in Manual to configure the router
Page 7 / 97
2
1.1 Package List
°
1 x AR-7284WnA or AR-7284WnB
°
1 x external splitter
°
1 x power adapter
°
2 x telephone cables (RJ-11)
°
1 x Ethernet cable (RJ-45)
°
1 x Quick Installation Guide(QIG)
°
1 x CD (Multi-languages EZmax Wiard / QIG , USB driver
& English Manual)
Page 8 / 97
3
1.2 Safety Cautions
Follow the following instructions to prevent the device from
risks and damage caused by fire or electric power:
°
Use volume labels to mark the type of power.
°
Only use the power adapter packed within the device
package.
°
Pay attention to the power load of the electric outlet or
power extension cord. An overloaded power outlet or
damaged lines and plugs may cause electric shock or fire
accident. Check the power cords regularly. If you find any
damage, replace it as soon as possible.
°
It’s necessary to prepare proper space for heat
dissipation to avoid damage caused by overheating. The
long and thin holes on the device are designed for heat
dissipation and to ensure that the device works normally.
Do not cover these heat dissipation holes.
°
Do not put this device in high temperature environment
and avoid direct sunlight.
°
Do not put this device in humid or watery environment.
Do not spill any fluid on this device.
°
Do not connect this device to any PCs or electronic
products, unless our customer engineer or your
broadband provider instructs you to do so, because any
wrong connection may lead to electric or fire risk.
°
Do not place this device on an unstable surface.
Page 9 / 97
4
1.3 LEDs and Interfaces
Front Panel
Figure 1 Front panel
The following table describes the LEDs of the device.
LED
Color
Status
Description
Green
Off
The power is off.
On
The power is on and the initialization
is normal.
Red
On
The device is initiating.
Blinks
The firmware is upgrading.
LAN
1/2/3/4
Green
Off
No LAN link.
Blinks
Data is being transmitted through
the LAN interface.
On
The connection of LAN interface is
normal.
Green
Off
No WLAN connection.
Blinks
Data is transmitted through the
WLAN interface.
On
The connection of WLAN interface is
normal.
Green
Off
No USB signal is detected.
Blinks
Data is passing through USB port.
On
The USB interface is ready.
ADSL
Green
Off
Initial self-test is failed.
Blinks
The device is detecting DSL signal.
On
The
DSL
line
connection
is
established.
Internet
Green
Off
The device is running under Bridge
Page 10 / 97
5
LED
Color
Status
Description
mode,
DSL
connection
is
not
present, or the power is off.
On
Connected to network.
Red
On
Network connection failed.
WPS
Green
On
The WPS indicator will light for 5
minutes after the WPS service is
registered successfully.
Blink
Green
°
The WPS indicator will light for
0.2s, and then off for 0.1s when
the WPS button is pressed and
the network card is ready for
register.
°
The WPS indicator will blink
every 0.1s to indicate the WPS
service fails to register.
°
The WPS indicator lights for 5
times and off for 0.5s to indicate
there are two or more wireless
network cards register at the
same time.
Off
WPS service is not ready or WPS
service has been setup successfully.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top