Page 51 / 86
Scroll up to view Page 46 - 50
43
Address you have specified will be denied accessing to
the router.
Mac Address #1-8
Please enter the MAC Address of the wireless clients for
the filtering control.
5.3.
Advanced Setup
5.3.1.
Firewall
Parameter
Description
Firewall
When you enable the firewall function, it will protect you
from following attacks of WAN side:
z
SYN flooding attack
z
Ping of Death
z
Teardrop
z
Land attack
SPI
If you enable SPI, all traffics initiated from WAN site will
be blocked including DMZ, Virtual Server, etc.
5.3.2.
Routing
Page 52 / 86
44
z
Routing Table List
You can see the current routing table of the router here. If you want to add
another routing rule, please click “ADD ROUTE”.
Parameter
Description
Dest IP
Show the IP Address of the destination LAN.
Mask
Show the Subnet Mask of the destination LAN. If it shows
“8” that means the Subnet Mask is “255.0.0.0”; “16”
means the Subnet Mask is “255.255.0.0”; “24” means the
Subnet Mask is “255.255.255.0”.
Parameter
Description
Gateway IP
The next stop gateway of the path toward the destination
LAN. This is the IP of the neighbor router that this router
should communicate with on the path to the destination
LAN.
Metric
The number of hops (routers) to pass through to reach
the destination LAN. It must be between 1 and 15.
Device
Show the interface that go to the next hop (router), such
as LAN port.
Use
The counter for access time.
Page 53 / 86
45
Edit
Edit the route, this icon is not shown for system default
route.
Drop
Drop the route, this icon is not shown for system default
route.
z
Add Route
If you have another router with a LAN-to-LAN connection, you may need to
create a static routing on the router that is the gateway to Internet.
Page 54 / 86
46
Parameter
Description
Destination IP Address
Enter the IP Address of the destination LAN.
IP Subnet Mask
Enter the Subnet Mask address of the destination LAN.
Gateway IP Address
This is the gateway IP Address where packets are sent.
Enter the gateway IP Address and select the channel
(PVC) you want to configure.
Metric
The number of hops (routers) to pass through to reach
the destination LAN. It must be between 1 and 15.
Announced in RIP
Select “Yes”, this routing path will be propagated to other
hosts through RIP broadcasts. Select “No”, this routing
path will be kept private and it is not included in RIP
broadcasts.
5.3.3.
NAT
Page 55 / 86
47
5.3.3.1. NAT
Network Address Translation (NAT) allows multiple users at your local site to
access the Internet through a single Public IP Address or multiple Public IP
Addresses. NAT provides Firewall protection from hacker attacks and has the
flexibility to allow you to map Private IP Addresses to Public IP Addresses for key
services such as Websites and FTP.
Parameter
Description
Virtual Circuit
VPI (Virtual Path Identifier) and VCI (Virtual Channel
Identifier define a virtual circuit. Please select the
channel (PVC) you want to configure.
NAT Status
The activated or deactivated status for the NAT function
will be shown here.
Number of IPs
Select “Single” if you only have a public IP Address.
Select “Multiple” if you have multiple IP Addresses.
5.3.3.2. DMZ
The DMZ Host is a local computer exposed to the Internet. When setting a
particular internal IP Address as the DMZ Host, all incoming packets will be
checked by the firewall and NAT algorithms then passed to the DMZ Host.
For example, if you have a local client PC that cannot run an Internet application
(e.g. Games) properly from behind the NAT firewall, then you can open the client
up to unrestricted two-way Internet access by defining a DMZ Host.
19216811.live