1. Home
    2. /
  2. Manuals
    3. /
  3. ECI
    4. /
  4. B-FOCuS-312-TR
    5. /
  5. 3
Page 11 / 16 Scroll up to view Page 6 - 10
B-FOCuS Router 312+
User Guide
ECI Telecom Ltd. Proprietary
7
DWG# 458006-0833-010 A00
4
Safety Considerations
The B-FOCuS 312+ Router is designed for in-house desktop use only.
Therefore:
•
Do not expose to direct sunlight.
•
Do not expose to temperatures exceeding 40°C.
•
Do not immerse in water, and do not dampen or install in wet conditions.
Page 12 / 16
B-FOCuS Router 312+
User Guide
ECI Telecom Ltd. Proprietary
8
DWG# 458006-0833-010 A00
5
Buttons and LEDs
5.1
Buttons/Ports
This section describes the ports and buttons on the router.
Figure 2. B-FOCuS Router 312+ Back Panel
•
Reset Button.
To reset the router, press and release the Reset button;
after about 30 seconds the unit will become operational.
•
Restore to Factory Defaults.
You may need to restore the factory
defaults if the configuration of your unit is changed, if you lose both
network connectivity and the ability to interface to the unit via the web
interface, or following a failed software upgrade. To restore factory
defaults, press the Reset button for more than 10 seconds. The unit
reverts to its factory defaults and after about 30 seconds becomes
operational again.
•
LAN (Local Area Network) Port.
Connect to Ethernet network
devices, such as a PC, hub, switch, or router. Depending on the
connection, you may need a cross-over cable or a straight-through
cable.
•
Power.
Make sure you observe the proper power requirements.
•
ADSL Port.
WAN interface that connects directly to the phone line.
Reset
Button
LAN
Port
Power
ADSL
Port
On/Off
Button
Page 13 / 16
B-FOCuS Router 312+
User Guide
ECI Telecom Ltd. Proprietary
9
DWG# 458006-0833-010 A00
5.2
LED Descriptions
The following pictures show where the LED indicators are positioned on the
units. An explanation of each LED follows.
Figure 3. B-FOCuS Router 312+
•
Power LED.
Indicates that power is supplied to the unit.
•
ADSL Link.
This LED serves two purposes. If it is continuously lit, the
ADSL interface is successfully connected to a device through the WAN
port. If the LED flickers, the router is training.
•
LAN Link.
This LED serves two purposes. If it is continuously lit, the
Ethernet interface is successfully connected to a device through the
LAN port. If it flickers, network activity is in progress.
•
Internet Link.
The Internet LED is off if no connection is established or
the connection is not used. When it is green, an Internet connection has
been established.
Power
LED
Internet
Link
ADSL
Sync
LAN
LEDs
Page 14 / 16
B-FOCuS Router 312+
User Guide
ECI Telecom Ltd. Proprietary
10
DWG# 458006-0833-010 A00
5.3
LED Table
The LED table below can help diagnose problems.
Table 2. B-FOCuS Router LEDs
LED Status
Off
Green
Blinking
Power
Power not
applied
Normal
Operation
N/A
ADSL Link
ADSL line not
connected
ADSL line is
trained
ADSL line is
training
LAN Link
Wrong type of
Ethernet cable
used
Ethernet line is
connected
Ethernet traffic
is flowing
Internet Link
No Internet link
established
Internet link
established
N/A
Page 15 / 16
B-FOCuS Router 312+
User Guide
ECI Telecom Ltd. Proprietary
11
DWG# 458006-0833-010 A00
6
Troubleshooting
Below is a list of common problems. Before calling technical support, please
look through these issues to see if they help solve your problem.
6.1
The Router is not Functional
•
Check that the power LED is green.
•
Check that the network cables are installed correctly.
•
Check that the LAN and Internet Link LEDs are green.
•
Check that the ADSL Sync LED is green.
•
Make sure that your PC and the router are on the same network
segment. The router’s default IP address is 10.0.0.138; make sure that
your PC’s network adapter is within the same 10.0.0.x subnet. If you are
running Windows, you can open a DOS window and type IPCONFIG to
verify this data.
•
Ping the router from your PC.
a. From the desktop, click
Start > Run
.
b. In the Open box, type
c. A positive result displays as:
Reply from 10.0.0.138 bytes=32 time<10ms TTL=255.
•
Ping the WAN.
•
If you can ping the router and your protocols are configured correctly,
you should be able to ping the ISP’s network (your ISP should have
provided the IP address of their server). If you cannot ping the ISP’s
network, make sure you are using the correct protocols with the correct
VPI/VCI values.
•
Make sure NAT is enabled for your connection. If NAT is disabled your
router will not route frames correctly.
•
Disable proxies on your browser. If you access the router, and instead
of receiving the Login window, the browser displays a login redirection
message, you should verify that JavaScript support is enabled.

Rate

4 / 5 based on 1 vote.

Popular ECI Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top