DrayTek Vigor-2930 Router Manual PDF (Setup & Configuration Guide)

Page 201 / 298 Scroll up to view Page 196 - 200

igor2930 Series User’s Guide

193

ALERTING -

Indicates that a call is coming.

ACTIVE-

Indicates that the VoIP connection is launched.

Codec

Indicates the voice codec employed by present channel.

PeerID

The present in-call or out-call peer ID (the format may be IP

or Domain).

Elapse

The format is represented as hours:minutes:seconds.

Tx Pkts

Total number of transmitted voice packets during this

connection session.

Rx Pkts

Total number of received voice packets during this connection

session.

Rx Losts

Total number of lost packets during this connection session.

Rx Jitter

The jitter of received voice packets.

In Calls

The accumulating in-call times.

Out Calls

The accumulating out-call times.

Speaker Gain

The volume of present call.

Log

Display logs of VoIP calls.

3.12 ISDN

3.12.1 Basic Concept

ISDN means integrated services digital network that is an international communications

standard for sending voice, video, and data over digital telephone lines or normal telephone

wires.

Below shows the menu items for ISDN.

Page 202 / 298

Vigor2930 Series User’s Guide

194

3.12.2 General Settings

This web page allows you to enable ISDN function.

ISDN Port

Click

Enable

to open the ISDN port and

Disable

to close it.

Country Code

For proper operation on your local ISDN network, you should

choose the correct country code.

D-Channel Mode

It allows you to configure ISDN layer2 protocol as:

Point-to-Point

- Configure ISDN port to use static TEI

(Terminal Endpoint Identifier).

Point-to-Multipoint

- Configure ISDN port to use Dynamic

TEI.

Own Number

Enter your ISDN number that you got from ISDN service

provider (To have such number, you have offer your request

from ISDN service provider first). Every outgoing call will

carry the number to the receiver.

Blocked MSN Numbers for

the router

Enter the specified MSN number into the fields to prevent

the router from dialing the specific MSN number

MSN Numbers for the

Router

MSN Numbers mean that the router is able to accept only

number-matched incoming calls. In addition, local ISDN

network provider should support MSN services. The router

Page 203 / 298

igor2930 Series User’s Guide

195

provides ten fields for MSN numbers. Note that MSN service

must be acquired from your local telecom operators. By

default, MSN function is disabled. If you leave the fields

blank, all incoming calls will be accepted without number

matching.

1-10 fields

– Fill in the portion that is different with the own

number.

For example, the own number is

1234567

and MSN numbers

are

12345

50

,

12345

17

and

12345

82

respectively. You can

type in

1234567

in the filed of own number. Fill in

50

,

17

and

67

on the fields of 1, 2 and 3 one by one without typing

12345.

Mapping to Phone Ports

For loop through phone calls, you can assign Phone 1, Phone

2, ISDN1-S0 as ring ports if incoming calls correspond with

settings on MSN number field.

There are ten internal lines (30-39) under ISDN1-S0 for you

to configure as dedicated line.

You can setup your ISDN

phone with one of these 10 different internal MSN

numbers.

Transparent

means

MSN on TE

port can

connect to NT port without limitation on the number among

30 ~ 39.

Any

means all the phones under ISDN1-S0

would ring.

w

If you choose

Any

as ISDN-S0 port, when the router receives

the incoming phone call with certain number for reaching

ISDN-S0, all the phone sets connected to ISDN-S0 will ring at

the same time.

Phone CLIR/CLIP

CLIR means “Calling Line Identification Restriction”. If you

choose this item, we will not let remote side see your phone

number.

Such function depends on environment that ISP

offers to you. Usually, hidden telephone number is not

permitted under many real circumstances.

CLIP means “Calling Line Identification Presentation”.

Usually the router will send "Own Number" to the remote side.

However

Own number

will restrict the router displaying only

one number on remote side. Vigor2930 series can connect up

to 6

phones at the same time. Therefore, if

CLIP

is selected, the

external MSN numbers that you setup will be displayed to

remote side

.

Page 204 / 298

Vigor2930 Series User’s Guide

196

Application Example

You got ISDN numbers with

5972720~5972729

from your ISP, and you try to connect

ISDN-TE port to ISDN network. Please refer to the following configuration.

Open

ISDN>> General Setup

and set as the following:

When remote user calls you by dialing

5972727

, the router will make Phone1 port ringing.

When remote user calls you by dialing

5972728

, the router will make ISDN phone under

ISDN1-S0 port and configured

with internal MSN number

32 ringing.

When remote user calls you by dialing

5972729

, the router will make ISDN phones under

ISDN1-S0 port and configured

with internal MSN number

5972729

ringing.

When remote user calls you by dialing

5972720

, the router will make all of ISDN phones

under ISDN1-S0 port ringing.

When remote user calls you by dialing

5972722

, the router will make no phone ringing for

the number is not specified in such page.

If you use Phone1 to dial an outgoing call: remote user will see the telephone number -

5972726 because CLIP is not checked.

If you use ISDN1-S0 with

MSN 32

to dial an outgoing call: remote user will see “Withheld

Number” from the telephone display panel because Phone CLIR is checked.

If you use

ISDN1-S0 with MSN 5972729

to dial an outgoing call: remote user will see the

number 5972729 because Phone CLIP is checked.

If you use

ISDN1-S0 without MSN Setup

to dial an outgoing call: remote user will see the

number 5972720 because Phone CLIP is checked.

Page 205 / 298

igor2930 Series User’s Guide

197

3.12.3 Dial to Single/Dual ISPs

Select

Dialing to a Single ISP

if you access the Internet via a single ISP.

ISP Access Setup

ISP Name -

Enter your ISP name such as Seednet, Hinet and

so on.

Dial Number -

Enter the ISDN access number provided by

your ISP.

Username -

Enter the username provided by your ISP.

Password -

Enter the password provided by your ISP.

Require ISP Callback (CBCP) -

If your ISP supports the

callback function, check this box to activate the Callback

Control Protocol during the PPP negotiation.

Scheduler (1-15) -

Enter the index of schedule profiles to

control the Internet access according to the preconfigured

schedules. Refer to section

3.8.2 Schedule

for detailed

configuration.

PPP/MP Setup

Link Type

–

There are three link types provided here for

different purpose.

Link Disable

disables the ISDN dial-out

function.

Dialup 64Kbps

allows you to use one ISDN B

channel for Internet access.

Dialup 128Kbps

allows you to

use both ISDN B channels for Internet access.

Dialup BOD

(for detailed information of configuration, please refer to

section

3.12.4

) stands for bandwidth-on-demand. The router

will use only one B channel in low traffic situations. Once the

single B channel bandwidth is fully used, the other B channel

will be activated automatically through the dialup. For more

detailed BOD parameter settings, please refer to the section of

Call Control

.

PPP Authentication -

PAP only allows you to configure the

PPP session to use the PAP protocol to negotiate the username

and password with the ISP.

PAP or CHAP

is to configure the

PPP session to use the PAP or CHAP protocols to negotiate

the username and password with the ISP.

Idle Timeout -

Idle timeout means the router will be

disconnect after being idle for a preset amount of time. The

default is 180 seconds. If you set the time to 0, the ISDN

connection to the ISP will always remain on.

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share