Page 216 / 251
Scroll up to view Page 211 - 215
Vigor2920 Series User’s Guide
206
general settings in
IPSec General Setup
, such as the pre-shared key that both parties
have known.
3.
Go to
LAN-to-LAN
. Click on one index number to edit a profile.
4.
Set
Common Settings
as shown below. You should enable both of VPN connections
because any one of the parties may start the VPN connection.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 217 / 251
Vigor2920 Series User’s Guide
207
5.
Set
Dial-Out Settings
as shown below to dial to connect to Router B aggressively with
the selected Dial-Out method.
If an
IPSec-based
service is selected, you should further specify the remote peer IP
Address, IKE Authentication Method and IPSec Security Method for this Dial-Out
connection.
If a
PPP-based service
is selected, you should further specify the remote peer IP Address,
Username, Password, PPP Authentication and VJ Compression for this Dial-Out
connection.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 218 / 251
Vigor2920 Series User’s Guide
208
6.
Set
Dial-In settings
to as shown below to allow Router B dial-in to build VPN
connection.
If an
IPSec-based
service is selected, you may further specify the remote peer IP
Address, IKE Authentication Method and IPSec Security Method for this Dial-In
connection. Otherwise, it will apply the settings defined in
IPSec General Setup
above.
If a
PPP-based service
is selected, you should further specify the remote peer IP Address,
Username, Password, and VJ Compression for this Dial-In connection.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 219 / 251
Vigor2920 Series User’s Guide
209
7.
At last, set the remote network IP/subnet in
TCP/IP Network Settings
so that Router A
can direct the packets destined to the remote network to Router B via the VPN
connection.
Settings in Router B in the remote office:
1.
Go to
VPN and Remote Access
and select
Remote Access Control
to enable the
necessary VPN service and click
OK
.
2.
Then, for using
PPP based
services, such as PPTP, L2TP, you have to set general
settings in
PPP General Setup
.
For using
IPSec-based
service, such as IPSec or L2TP with IPSec Policy, you have to
set general settings in
IPSec General Setup
, such as the pre-shared key that both parties
have known.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 220 / 251
Vigor2920 Series User’s Guide
210
3.
Go to
LAN-to-LAN
. Click on one index number to edit a profile.
4.
Set
Common Settings
as shown below. You should enable both of VPN connections
because any one of the parties may start the VPN connection.
5.
Set
Dial-Out Settings
as shown below to dial to connect to Router B aggressively with
the selected Dial-Out method.
If an
IPSec-based
service is selected, you should further specify the remote peer IP
Address, IKE Authentication Method and IPSec Security Method for this Dial-Out
connection.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
19216811.live