1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor-2920
    5. /
  5. 35
Page 171 / 251 Scroll up to view Page 166 - 170
Vigor2920 Series User’s Guide
161
User Name
This field is applicable when you select, PPTP or L2TP with or
without IPSec policy above.
Password
This field is applicable when you select PPTP or L2TP with or
without IPSec policy above.
PPP Authentication
This field is applicable when you select, PPTP or L2TP with or
without IPSec policy above. PAP/CHAP is the most common
selection due to wild compatibility.
VJ compression
This field is applicable when you select PPTP or L2TP with or
without IPSec policy above. VJ Compression is used for
TCP/IP protocol header compression. Normally set to
Yes
to
improve bandwidth utilization.
IKE Authentication
Method
This group of fields is applicable for IPSec Tunnels and L2TP
with IPSec Policy.
Pre-Shared Key
- Input 1-63 characters as pre-shared key.
Digital Signature (X.509)
- Select one predefined Profiles set
in the
VPN and Remote Access >>IPSec Peer Identity
.
IPSec Security Method
This group of fields is a must for IPSec Tunnels and L2TP with
IPSec Policy.
Medium
Authentication Header (AH)
means data will be authenticated,
but not be encrypted. By default, this option is active.
High (ESP-Encapsulating Security Payload)-
means payload
(data) will be encrypted and authenticated. Select from below:
DES without Authentication
-Use DES encryption algorithm
and not apply any authentication scheme.
DES with Authentication-
Use DES encryption algorithm and
apply MD5 or SHA-1 authentication algorithm.
3DES without Authentication
-Use triple DES encryption
algorithm and not apply any authentication scheme.
3DES with Authentication-
Use triple DES encryption
algorithm and apply MD5 or SHA-1 authentication algorithm.
AES without Authentication
-Use AES encryption algorithm
and not apply any authentication scheme.
AES with Authentication-
Use AES encryption algorithm and
apply MD5 or SHA-1 authentication algorithm.
Advanced
Specify mode, proposal and key life of each IKE phase,
Gateway, etc.
The window of advance setup is shown as below:
IKE phase 1 mode -
Select from
Main
mode and
Aggressive
mode. The ultimate outcome is to exchange security proposals
to create a protected secure channel.
Main
mode is more secure
than
Aggressive
mode since more exchanges are done in a
secure channel to set up the IPSec session. However, the
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 172 / 251
Vigor2920 Series User’s Guide
162
Aggressive
mode is faster. The default value in Vigor router is
Main mode.
IKE phase 1 proposal-
To propose the local available
authentication schemes and encryption algorithms to the VPN
peers, and get its feedback to find a match. Two combinations
are available for Aggressive mode and nine for
Main
mode. We
suggest you select the combination that covers the most
schemes.
IKE phase 2 proposal-
To propose the local available
algorithms to the VPN peers, and get its feedback to find a
match. Three combinations are available for both modes. We
suggest you select the combination that covers the most
algorithms.
IKE phase 1 key lifetime-
For security reason, the lifetime of
key should be defined. The default value is 28800 seconds. You
may specify a value in between 900 and 86400 seconds.
IKE phase 2 key lifetime-
For security reason, the lifetime of
key should be defined. The default value is 3600 seconds.
You may specify a value in between 600 and 86400 seconds.
Perfect Forward Secret (PFS)-
The IKE Phase 1 key will be
reused to avoid the computation complexity in phase 2. The
default value is inactive this function.
Local ID -
In
Aggressive
mode, Local ID is on behalf of the IP
address while identity authenticating with remote VPN server.
The length of the ID is limited to 47 characters.
Allowed Dial-In Type
Determine the dial-in connection with different types.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 173 / 251
Vigor2920 Series User’s Guide
163
PPTP
Allow the remote dial-in user to make a PPTP VPN connection
through the Internet. You should set the User Name and
Password of remote dial-in user below.
IPSec Tunnel
Allow the remote dial-in user to trigger an IPSec VPN
connection through Internet.
L2TP
Allow the remote dial-in user to make a L2TP VPN connection
through the Internet. You can select to use L2TP alone or with
IPSec. Select from below:
None -
Do not apply the IPSec policy. Accordingly, the VPN
connection employed the L2TP without IPSec policy can be
viewed as one pure L2TP connection.
Nice to Have
- Apply the IPSec policy first, if it is applicable
during negotiation. Otherwise, the dial-in VPN connection
becomes one pure L2TP connection.
Must -
Specify the IPSec policy to be definitely applied on the
L2TP connection.
Specify Remote VPN
Gateway
You can specify the IP address of the remote dial-in user or
peer ID (should be the same with the ID setting in dial-in
type) by checking the box. Also, you should further specify
the corresponding security methods on the right side.
If you uncheck the checkbox
,
the connection type you select
above will apply the authentication methods and security
methods in the general settings.
User Name
This field is applicable when you select PPTP or L2TP with or
without IPSec policy above.
Password
This field is applicable when you select PPTP or L2TP with or
without IPSec policy above.
VJ Compression
VJ Compression is used for TCP/IP protocol header
compression. This field is applicable when you select PPTP or
L2TP with or without IPSec policy above.
IKE Authentication
Method
This group of fields is applicable for IPSec Tunnels and
L2TP with IPSec Policy when you specify the IP address of
the remote node. The only exception is Digital Signature
(X.509) can be set when you select IPSec tunnel either with
or without specify the IP address of the remote node.
Pre-Shared Key -
Check the box of Pre-Shared Key to
invoke this function and type in the required characters
(1-63) as the pre-shared key.
Digital Signature (X.509) –
Check the box of Digital
Signature to invoke this function and select one predefined
Profiles set in the
VPN and Remote Access >>IPSec Peer
Identity
.
IPSec Security Method
This group of fields is a must for IPSec Tunnels and L2TP with
IPSec Policy when you specify the remote node.
Medium-
Authentication Header (AH) means data will be
authenticated, but not be encrypted. By default, this option is
active.
High-
Encapsulating Security Payload (ESP) means payload
(data) will be encrypted and authenticated. You may select
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 174 / 251
Vigor2920 Series User’s Guide
164
encryption algorithm from Data Encryption Standard (DES),
Triple DES (3DES), and AES.
My WAN IP
This field is only applicable when you select PPTP or L2TP
with or without IPSec policy above. The default value is 0.0.0.0,
which means the Vigor router will get a PPP IP address from
the remote router during the IPCP negotiation phase. If the PPP
IP address is fixed by remote side, specify the fixed IP address
here. Do not change the default value if you do not select PPTP
or L2TP.
Remote Gateway IP
This field is only applicable when you select PPTP or L2TP
with or without IPSec policy above. The default value is 0.0.0.0,
which means the Vigor router will get a remote Gateway PPP
IP address from the remote router during the IPCP negotiation
phase. If the PPP IP address is fixed by remote side, specify the
fixed IP address here. Do not change the default value if you do
not select PPTP or L2TP.
Remote Network IP/
Remote Network Mask
Add a static route to direct all traffic destined to this Remote
Network IP Address/Remote Network Mask through the VPN
connection. For IPSec, this is the destination clients IDs of
phase 2 quick mode.
More
Add a static route to direct all traffic destined to more Remote
Network IP Addresses/ Remote Network Mask through the
VPN connection. This is usually used when you find there are
several subnets behind the remote VPN router.
RIP Direction
The option specifies the direction of RIP (Routing Information
Protocol) packets. You can enable/disable one of direction here.
Herein, we provide four options: TX/RX Both, TX Only, RX
Only, and Disable.
From first subnet to
remote network, you
have to do
If the remote network only allows you to dial in with single
IP, please choose
NAT
, otherwise choose
Route
.
Change default route to
this VPN tunnel
Check this box to change the default route with this VPN
tunnel.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 175 / 251
Vigor2920 Series User’s Guide
165
4.9.7 Connection Management
You can find the summary table of all VPN connections. You may disconnect any VPN
connection by clicking
Drop
button. You may also aggressively Dial-out by using Dial-out
Tool and clicking
Dial
button.
Dial
Click this button to execute dial out function.
Refresh Seconds
Choose the time for refresh the dial information among 5, 10,
and 30.
Refresh
Click this button to refresh the whole connection status.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299

Rate

124.8 / 5 based on 304 votes.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top