DrayTek Vigor2860n-plus Router Manual PDF (Setup & Configuration Guide)

Page 266 / 794 Scroll up to view Page 261 - 265

Vigor2860 Series User’s Guide

252

check this box to push ACK of upload faster to speed the

network traffic.

Limited_bandwidth Ratio

The ratio typed here is reserved for limited bandwidth of

UDP application.

Note:

The rate of outbound/inbound must be smaller than the real bandwidth to ensure

correct calculation of QoS. It is suggested to set the bandwidth value for inbound/outbound

as 80% - 85% of physical network speed provided by ISP to maximize the QoS

performance.

Edit the Class Rule for QoS

1.

The first three (Class 1 to Class 3) class rules can be adjusted for your necessity. To add,

edit or delete the class rule, please click the

Edit

link of that one.

2.

After you click the

Edit

link, you will see the following page. Now you can define the

name for that Class. In this case, “Test” is used as the name of Class Index #1.

Page 267 / 794

Vigor2860 Series User’s Guide

253

3.

For adding a new rule, click

Add

to open the following page.

Available settings are explained as follows:

Item

Description

ACT

Check this box to invoke these settings.

Ethernet Type

Please specify which protocol (IPv4 or IPv6) will be used

for this rule.

Local Address

Click the

Edit

button to set the local IP address (on LAN)

for the rule.

Remote Address

Click the

Edit

button to set the remote IP address (on

LAN/WAN) for the rule.

Address Type –

Determine the address type for the source

address.

For

Single Address

, you have to fill in Start IP address.

For

Range Address

, you have to fill in Start IP address and

End IP address.

For

Subnet Address

, you have to fill in Start IP address

and Subnet Mask.

DiffServ CodePoint

All the packets of data will be divided with different levels

and will be processed according to the level type by the

system. Please assign one of the levels of the data for

processing with QoS control.

Service Type

It determines the service type of the data for processing

with QoS control. It can also be edited. You can choose the

predefined service type from the Service Type drop down

list. Those types are predefined in factory. Simply choose

the one that you want for using by current QoS.

4.

After finishing all the settings here, please click

OK

to save the configuration.

Page 268 / 794

Vigor2860 Series User’s Guide

254

By the way, you can set up to 20 rules for one Class. If you want to edit an existed rule, please

select the radio button of that one and click

Edit

to open the rule edit page for modification.

Edit the Service Type for Class Rule

1.

To add a new service type, edit or delete an existed service type, please click the Edit

link under Service Type field.

2.

After you click the

Edit

link, you will see the following page.

Page 269 / 794

Vigor2860 Series User’s Guide

255

3.

For adding a new service type, click

Add

to open the following page.

Available settings are explained as follows:

Item

Description

Service Name

Type in a new service for your request. The maximum

length of the name you can set is 11 characters.

Service Type

Choose the type (TCP, UDP or TCP/UDP or other) for the

new service.

Port Configuration

Type

- Click

Single

or

Range

as the

Type

. If you select

Range, you have to type in the starting port number and the

end porting number on the boxes below.

Port Number

– Type in the starting port number and the

end porting number here if you choose Range as the type.

5.

After finishing all the settings here, please click

OK

to save the configuration.

By the way, you can set up to 10 service types. If you want to edit/delete an existed service

type, please select the radio button of that one and click

Edit/Edit

for modification.

Page 270 / 794

Vigor2860 Series User’s Guide

256

Retag the Packets for Identification

Packets coming from LAN IP can be retagged through QoS setting. When the packets sent out

through WAN interface, all of them will be tagged with certain header and that will be easily

to be identified by server on ISP.

For example, in the following illustration, the VoIP packets in LAN go into Vigor router

without any header. However, when they go forward to the Server on ISP through Vigor

router, all of the packets are tagged with AF (configured in Bandwidth >>QoS>>Class)

automatically.

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share