DrayTek Vigor-2800G Router Manual PDF (Setup & Configuration Guide)

Page 106 / 202 Scroll up to view Page 101 - 105

Vigor2800 Series User’s Guide

100

Enable

Check this box to invoke this setting.

Prefix Number

The phone number set here is used to add, strip, or replace the

OP number.

Mode

None

- No action.

Add

- When you choose this mode, the OP number will be

added with the prefix number for calling out through the

specific VoIP interface.

Strip

- When you choose this mode, the OP number will be

deleted by the prefix number for calling out through the

specific VoIP interface. Take the above picture (Prefix Table

Setup web page) as an example, the OP number of

886

will be

deleted completely for the prefix number is set with

886

.

Replace

- When you choose this mode, the OP number will be

replaced by the prefix number for calling out through the

specific VoIP interface. Take the above picture (Prefix Table

Setup web page) as an example, the prefix number of 03 will

be replaced by 8863. For example: dial number of

“031111111” will be changed to “88631111111” and sent to

SIP server.

Page 107 / 202

Vigor2800 Series User’s Guide

101

OP Number

The front number you type here is the first part of the account

number that you want to execute special function (according

to the chosen mode) by using the prefix number.

Min Len

Set the minimal length of the dial number for applying the

prefix number settings. Take the above picture (Prefix Table

Setup web page) as an example, if the dial number is between

7 and 9, that number can apply the prefix number settings

here.

Max Len

Set the maximum length of the dail number for applying the

prefix number settings.

Interface

Choose the one that you want to enable the prefix number

settings from the

six

pre-saved SIP accounts.

3.9.2 SIP Accounts

In this section, you set up your own SIP settings. When you apply for an account, your SIP

service provider will give you an

Account Name

or user name,

SIP Registrar, Proxy,

and

Domain name

. (The last three might be the same in some case). Then you can tell your folks

your SIP Address as in

Account Name@ Domain name

As Vigor VoIP Router is turned on, it will first register with Registrar using

AuthorizationUser@Domain/Realm. After that, your call will be bypassed by SIP Proxy to

the destination using AccountName@Domain/Realm as identity.

Index

Click this link to access into next page for setting SIP account.

Profile

Display the profile name of the account.

Domain/Realm

Display the domain name or IP address of the SIP registrar

server.

Proxy

Display the domain name or IP address of the SIP proxy

server.

Account Name

Display the account name of SIP address before @.

Page 108 / 202

Vigor2800 Series User’s Guide

102

Ring Port

Specify which port will ring when receiving a phone call. The

ISDN ring port is available for Vigor2800VGi only.

STUN Server

Type in the IP address of the STUN server.

External IP

Type in the gateway IP address.

SIP PING interval

The default value is 150sec. It is useful for a Nortel server

NAT Traversal Support.

Status

Show the status for the corresponding SIP account.

R

means

such account is registered on SIP server successfully.

–

means

the account is failed to register on SIP server.

Profile Name

Assign a name for this profile for identifying. You can type

similar name with the domain. For example, if the domain

name is

draytel.org

, then you might set

draytel-1

in this field.

Register via

If you want to make VoIP call without register personal

information, please choose

None

and check the box to achieve

the goal.

Some SIP server allows user to use VoIP function

without registering. For such server, please check the box of

make call without register

. Choosing

Auto

is recommended.

The system will select a proper way for your VoIP call.

SIP Port

Set the port number for sending/receiving SIP message for

building a session. The default value is

5060.

Your peer must

set the same value in his/her Registrar.

Domain/Realm

Set the domain name or IP address of the SIP Registrar server.

Page 109 / 202

Vigor2800 Series User’s Guide

103

Proxy

Set domain name or IP address of SIP proxy server. By the

time you can type

:port

number after the domain name to

specify that port as the destination of data transmission (e.g.,

nat.draytel.org

:5065

)

Act as Outbound Proxy

Check this box to make the proxy acting as outbound proxy.

Display Name

The caller-ID that you want to be displayed on your friend’s

screen.

Account Number/Name

Enter your account name of SIP Address, e.g. every text

before @.

Authentication ID

Check the box to invoke this function and enter the name or

number used for SIP Authorization with SIP Registrar. If this

setting value is the same as Account Name, it is not necessary

for you to check the box and set any value in this field.

Password

The password provided to you when you registered with a SIP

service.

Expiry Time

The time duration that your SIP Registrar server keeps your

registration record. Before the time expires, the router will

send another register request to SIP Registrar again.

NAT Traversal Support

If the router (e.g.

,

broadband router) you use connects to

internet by other device, you have to set this function for your

necessity.

None –

Disable this function.

Stun

– Choose this option if there is Stun server provided for

your router.

Manual

– Choose this option if you want to specify an

external IP address as the NAT transversal support.

Nortel

– If the soft-switch that you use supports nortel

solution, you can choose this option.

Ring Port

Set VoIP 1,VoIP 2, or ISDN as the default ring port for this

SIP account. The ISDN ring port is available for

Vigor2800VGi only.

Ring Pattern

Choose a ring tone type for the VoIP phone call.

Page 110 / 202

Vigor2800 Series User’s Guide

104

Below shows successful SIP accounts for your reference.

3.9.3 Phone Settings

This page allows user to set phone settings for VoIP 1 and VoIP 2 respectively.

Note:

ISDN port (Index 3) is available for the users living in Europe and using

Vigor 2800VGi only.

Phone List

Port –

There are three phone ports provided here for you to

configure.

Call feature

– A brief description for call feature will be

shown in this field for your reference.

Codec

– The default Codec setting for each port will be

shown in this field for your reference. You can click the

number below the Index field to change it for each phone port.

Tone

- Display the tone settings that configured in the

advanced settings page of Phone Index.

Gain

- Display the volume gain settings for Mic/Speaker that

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share