Page 11 / 335 Scroll up to view Page 6 - 10
Vigor2710 Series User’s Guide
xi
Trouble Shooting
.........................................................................................
317
6.1 Checking If the Hardware Status Is OK or Not
....................................................................
317
6.2 Checking If the Network Connection Settings on Your Computer Is OK or Not
.................
318
6.3 Pinging the Router from Your Computer
.............................................................................
320
6.4 Checking If the ISP Settings are OK or Not
........................................................................
321
6.5 Backing to Factory Default Setting If Necessary
................................................................
322
6.6 Contacting Your Dealer
.......................................................................................................
323
Page 12 / 335
Page 13 / 335
Vigor2710 Series User’s Guide
1
1
P
P
r
r
e
e
f
f
a
a
c
c
e
e
Vigor2710 series is an ADSL router. It integrates IP layer QoS, NAT session/bandwidth
management to help users control works well with large bandwidth.
By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DS, the
router increases the performance of VPN greatly, and offers several protocols (such as
IPSec/PPTP/L2TP) with up to 2 VPN tunnels.
The object-based design used in SPI (Stateful Packet Inspection) firewall allows users to set
firewall policy with ease. CSM (Content Security Management) provides users control and
management in IM (Instant Messenger) and P2P (Peer to Peer) more efficiency than before.
By the way, DoS/DDoS prevention and URL/Web content filter strengthen the security
outside and control inside.
Object-based firewall is flexible and allows your network be safe. In addition, through VoIP
function, the communication fee for you and remote people can be reduced.
In addition, Vigor2710 series supports USB interface for connecting USB printer to share
printer or USB storage device for sharing files. Vigor2710 series provides two-level
management to simplify the configuration of network connection. The user operation allows
user accessing into WEB interface via simple configuration. However, if users want to have
advanced configurations, they can access into WEB interface through administration
operation.
1.1 Web Configuration Buttons Explanation
Several main buttons appeared on the web pages are defined as the following:
Save and apply current settings.
Cancel current settings and recover to the previous saved settings.
Clear all the selections and parameters settings, including selection from
drop-down list. All the values must be reset with factory default settings.
Add new settings for specified item.
Edit the settings for the selected item.
Delete the selected item with the corresponding settings.
Note:
For the other buttons shown on the web pages, please refer to Chapter 4 for detailed
explanation.
Page 14 / 335
Vigor2710 Series User’s Guide
2
1.2 LED Indicators and Connectors
Before you use the Vigor router, please get acquainted with the LED indicators and
connectors first.
1.2.1 For Vigor2710
LED
Status
Explanation
Blinking
The router is powered on and running
normally.
ACT
(Activity)
Off
The router is powered off.
CSM
On
The profile(s) of CSM (Content Security
Management) for IM/P2P, URL/Web
Content Filter application can be enabled
from
Firewall >>General Setup
. (Such
profile must be established under
CSM
menu).
On
The router is ready to access Internet
through DSL link.
DSL
Blinking
Slowly: The modem is ready.
Quickly: The connection is training.
On
The port is connected.
Off
The port is disconnected.
LAN 1/2/3/4
Blinking
The data is transmitting.
On
A USB device is connected and active.
USB
Blinking
The data is transmitting.
VPN
On
The VPN tunnel is active.
QoS
On
The QoS function is active.
On
The DoS/DDoS function is active.
DoS
Blinking
It will blink while detecting an attack.
WCF
On
The profile(s) of CSM (Content Security
Management) for Web Content Filter
application can be enabled from
Firewall
>>General Setup
. (Such profile must be
established under
CSM
menu)
Interface
Description
DSL
Connecter for accessing the Internet through ADSL2/2+.
LAN (1-4)
Connecters for local networked devices.
USB
Connecter for USB storage device (Pen Driver/Mobile
HD) or printer.
Page 15 / 335
Vigor2710 Series User’s Guide
3
Interface
Description
Factory Reset
Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the
hole and keep for more than 5 seconds. When you see the ACT LED begins to blink
rapidly than usual, release the button. Then the router will restart with the factory default
configuration.
PWR
Connecter for a power adapter.
ON/OFF
Power Switch.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top