Page 176 / 357
Scroll up to view Page 171 - 175
Vigor2830 Series User’s Guide
164
Setup
All the schedules can be set previously in
Application >>
Schedule
web page and you can use the number that you have
set in that web page.
4.5.3 User Group
This page allows you to bind several user profiles into one group. These groups will be used in
Firewall>>General Setup
as part of filter rules.
Please click any index number link to open the following page.
Name
Type a name for this user group.
Available User Objects
You can gather user profiles (objects) from
User Profile
page
within one user group. All the available user objects that you
have created will be shown in this box. Notice that user object,
Admin and Dial-In User are factory settings. User defined
profiles will be numbered with 3, 4, 5 and so on.
Selected Keyword
Click
button to add the selected user objects in this
Page 177 / 357
Vigor2830 Series User’s Guide
165
Objects
box.
4.5.4 User Online Status
This page displays the user(s) connected to the router and refreshes the connection status in an
interval of several seconds.
Refresh Seconds
Use the drop down list to choose the time interval of
refreshing data flow that will be done by the system
automatically.
Refresh
Click this link to refresh this page manually.
Index
Display the number of the data flow.
Active User
Display the users which connect to Vigor router currently. You
can click the link under the username to open the user profile
setting page for that user.
IP Address
Display the IP address of the device.
Last Login Time
Display the login time that such user connects to the router last
time.
Expired Time
Display the expired time of the network connection for the
user.
Idle Time
Display the idle timeout setting for such profile.
Action
Block
- can prevent specified user accessing into Internet.
Unblock
– the user will be blocked.
Logout
– the user will be logged out forcefully.
Page 178 / 357
Vigor2830 Series User’s Guide
166
4.6 Objects Settings
For IPs in a range and service ports in a limited range usually will be applied in configuring
router’s settings, therefore we can define them with
objects
and bind them with
groups
for
using conveniently. Later, we can select that object/group that can apply it. For example, all
the IPs in the same department can be defined with an IP object (a range of IP address).
4.6.1 IP Object
You can set up to 192 sets of IP Objects with different conditions.
Set to Factory Default
Clear all profiles.
Page 179 / 357
Vigor2830 Series User’s Guide
167
Click the number under Index column for settings in detail.
Name
Type a name for this profile. Maximum 15 characters are
allowed.
Interface
Choose a proper interface.
For example, the
Direction
setting in
Edit Filter Rule
will
ask you specify IP or IP range for WAN or LAN or any IP
address. If you choose LAN as the
Interface
here, and choose
LAN as the direction setting in
Edit Filter Rule
, then all the
IP addresses specified with LAN interface will be opened for
you to choose in
Edit Filter Rule
page.
Address Type
Determine the address type for the IP address.
Select
Single Address
if this object contains one IP address
only.
Select
Range Address
if this object contains several IPs
within a range.
Select
Subnet Address
if this object contains one subnet for
IP address.
Select
Any Address
if this object contains any IP address.
Select
Mac Address
if this object contains Mac address.
MAC Address
Type the MAC address of the network card which will be
controlled.
Start IP Address
Type the start IP address for Single Address type.
Page 180 / 357
Vigor2830 Series User’s Guide
168
End IP Address
Type the end IP address if the Range Address type is selected.
Subnet Mask
Type the subnet mask if the Subnet Address type is selected.
Invert Selection
If it is checked, all the IP addresses except the ones listed
above will be applied later while it is chosen.
Below is an example of IP objects settings.
4.6.2 IP Group
This page allows you to bind several IP objects into one IP group.
Set to Factory Default
Clear all profiles.
19216811.live