1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. WBR-1310v2
    5. /
  5. 5
Page 21 / 74 Scroll up to view Page 16 - 20
±1
D-Link WBR-1310 User Manual
Section 3 - Configuration
Select
Dynamic
(most common) or
Static
. Select
Static
if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server
Addresses (Static PPTP only).
Enter the Gateway IP Address provided by your ISP.
The DNS server information will be supplied by your
ISP (Internet Service Provider.)
Enter the Server IP provided by your ISP (optional).
Enter your PPTP account name.
Enter your PPTP password and then retype the
password in the next box.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the
default MTU.
Select either Always-on, Manual, or Connect-on demand.
PPTP:
IP Address:
Subnet Mask:
Gateway:
DNS:
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with
a username and password. This option is typically used for DSL services.
Server IP:
PPTP Account:
PPTP Password:
Maximum Idle
Time:
MTU:
Connect Mode:
Page 22 / 74
±±
D-Link WBR-1310 User Manual
Section 3 - Configuration
Select
Dynamic
(most common) or
Static
. Select
Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses.
Enter the IP address (Static L2TP only).
Enter the Primary and Secondary DNS Server Addresses
(Static L2TP only).
Enter the Gateway IP Address provided by your ISP.
The DNS server information will be supplied by your ISP
(Internet Service Provider.)
Enter the Server IP provided by your ISP (optional).
Enter your L2TP account name.
Enter your L2TP password and then retype the password
in the next box.
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the
default MTU.
Select either Always-on, Manual, or Connect-on demand.
L2TP:
IP Address:
Subnet Mask:
Gateway:
DNS:
Server IP:
L2TP Account:
L2TP Password:
Maximum Idle
Time:
MTU:
Connect Mode:
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
Page 23 / 74
±3
D-Link WBR-1310 User Manual
Section 3 - Configuration
Enter your Big Pond user name.
Enter your Big Pond password and then retype
the password in the next box.
Enter the IP address of the login server.
Enter the IP address of the login server.
The default MAC Address is set to the WAN’s
physical interface MAC address on the
Broadband Router. It is not recommended that
you change the default MAC address unless
required by your ISP.
The default MAC address is set to the WAN’s
physical interface MAC address on the
Broadband Router. You can use the “Clone
MAC Address” button to copy the MAC address
of the Ethernet Card installed by your ISP and
replace the WAN MAC address with the MAC
address of the router. It is not recommended
that you change the default MAC address unless
required by your ISP.
User Name:
Password:
Auth Server:
Login Server IP:
MAC Address:
Clone MAC
Address:
Internet Setup
Big Pond
Page 24 / 74
±²
D-Link WBR-1310 User Manual
Section 3 - Configuration
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The default MAC Address is set to the WAN’s
physical interface MAC address on the Broadband
Router. It is not recommended that you change
the default MAC address unless required by your
ISP.
The default MAC address is set to the WAN’s
physical interface MAC address on the Broadband
Router. You can use the
Clone MAC Address
button to copy the MAC address of the Ethernet
Card installed by your ISP and replace the WAN
MAC address with the MAC address of the router.
It is not recommended that you change the default
MAC address unless required by your ISP.
Enter the Primary DNS server IP address
assigned by your ISP.
This is optional.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is
the default MTU.
IP Address:
Subnet Mask:
ISP Gateway:
MAC Address:
Clone MAC
Address:
Primary DNS
Address:
Secondary DNS
Address:
MTU:
Internet Setup
Static (assigned by ISP)
Select Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask,
gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP
form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
Page 25 / 74
±³
D-Link WBR-1310 User Manual
Section 3 - Configuration
Check the box to enable the wireless function. If
you do not want to use wireless, uncheck the box
to disable all the wireless functions.
Service Set Identifier (SSID) is the name of your
wireless network. Create a name using up to 32
characters. The SSID is case-sensitive.
Indicates the channel setting for the WBR-2310.
By default the channel is set to 6. The Channel
can be changed to fit the channel setting for
an existing wireless network or to customize
the wireless network. The
Auto Channel Scan
setting can be selected to allow the WBR-2310
to choose the channel with the least amount of
interference.
Enable this mode if your network is made up of
purely 802.11g devices. If you have both 802.11b
and 802.11g wireless clients, uncheck the box.
Check this option if you would not like the SSID
of your wireless network to be broadcasted by the
WBR-2310. If this option is checked, the SSID of
the WBR-2310 will not be seen by Site Survey
utilities so your wireless clients will have to know
the SSID of your WBR-2310 in order to connect
to it.
Enable Wireless:
Wireless Channel:
Wireless Settings
Wireless Network
Name:
802.11g Only
Mode:
Enable Hidden
Wireless:

Rate

3.5 / 5 based on 2 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top