1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DWL-7200AP

D-Link DWL-7200AP Router Manual PDF (Setup & Configuration Guide)

Given below is full router user manual of D-Link DWL-7200AP router model. You can also download this manual in PDF Format to read later on your computer.

Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.

Page 1 / 12
This product can be set up using
This product can be set up using
This product can be set up using
This product can be set up using
This product can be set up using
an
an
an
an
any curr
y curr
y curr
y curr
y curren
en
en
en
ent W
t W
t W
t W
t Web br
eb br
eb br
eb br
eb browser
owser
owser
owser
owser, i.e
, i.e
, i.e
, i.e
, i.e.,
.,
.,
.,
.,
Internet Explorer 6 or Netscape
Internet Explorer 6 or Netscape
Internet Explorer 6 or Netscape
Internet Explorer 6 or Netscape
Internet Explorer 6 or Netscape
Navi
avi
avi
avi
avigator 6.2.3 or later
gator 6.2.3 or later
gator 6.2.3 or later
gator 6.2.3 or later
gator 6.2.3 or later.
©2004 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders.
Software and specifications subject to change without notice. DWL-7200AP. 09102004
Before You Begin
Check Your Package Contents
DWL-7200AP
Air
Premier
™
AG
Wireless Access Point
If any of the above items are missing, please contact your reseller.
The default IP address for the DWL-7200AP is
192.168.0.50
with a subnet mask of
255.255.255.0
. For the purpose of configuring the DWL-7200AP you will need to assign
your computer a static IP address within the same range as the DWL-7200AP’s IP
address.
See the Manual on the CD-ROM if you need assistance in assigning a static
IP address for your network adapter.
DWL-7200AP
D-Link
Air
Premier
TM
AG
Tri-mode Dualband Wireless
Access Point
CD-ROM with Manual
Ethernet (CAT5e UTP/Straight-Through) Cable
Using a power adapter
with a different voltage
rating will damage and void
the warranty of this product.
Power Adapter
PoE Base Unit
Power Cord
Page 2 / 12
2
Hardware Overview
Front Panel
Power LED:
Indicates
the unit is powered on.
Link/Act LEDs:
Indicates a 10M
or 100M Link to the LAN port.
Activity is indicated when blinking.
WLAN LEDs:
A solid light
indicates that the wireless
segment is ready. This LED
blinks during wireless data
transmission.
Page 3 / 12
3
Power Connector
The power adapter
connects here.
Reset Button
Pressing this button restores
the access point to its original
factory default settings.
LAN Port
Connects to a PC, switch,
router, or PoE base unit
using an Ethernet cable.
2.4GHz Antenna
Used to wirelessly connect
to 802.11b/g devices.
Rear Panel
Hardware Overview (continued)
5GHz Antenna
Used to wirelessly connect
to 802.11a devices.
Page 4 / 12
4
There are two methods of powering the DWL-7200AP. The power adapter can plug directly
into the unit or plug into the PoE (Power over Ethernet) base unit. To connect power
directly to the DWL-7200AP, please follow the steps on this page. To use the PoE base
unit, please follow the steps on the next page.
Connecting Power Directly to the DWL-7200AP
A.
Connect the power adapter to the
receptor
on the back panel of the DWL-7200AP.
Connect the power cord to the power adapter. Plug the other end of the power
cord into a wall outlet or power strip. The Power LED will turn
ON
to indicate
proper operation.
B.
Insert an Ethernet cable into the
LAN port
on the back panel of the
DWL-7200AP
and an available Ethernet port on the network adapter in the computer you will
use to configure the DWL-7200AP. The
Link
LED for the LAN Port will illuminate
to indicate a proper connection.
C.
Computers with 802.11a/b/g wireless adapters can connect to the DWL-7200AP.
The DWL-AG660
Air
Premier
TM
AG Wireless Cardbus Adapter and the DWL-AG530
Air
Premier
TM
AG Wireless PCI Adapter will connect with the DWL-7200AP, out of
the box, using the default settings.
Connecting The DWL-7200AP To
Your Network
Page 5 / 12
5
Connecting The DWL-7200AP To
Your Network (continued)
Connecting PoE (Power over Ethernet) to the DWL-7200AP
•
Step 1
: Connect one end of an Ethernet cable (included with your package) to the
LAN port
on the DWL-7200AP and the other end of the Ethernet cable to the port
labeled
P+DATA OUT
on the PoE base unit.
•
Step 2
: Connect another Ethernet cable from the
DATA IN
port on the PoE base unit
to your router/switch or to a PC.
•
Step 3
:
Attach the power adapter to the connector labeled
POWER IN
on the PoE
base unit. Attach the power cord to the power adapter and into an electrical outlet.

Rate

4.5 / 5 based on 2 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top