Page 121 / 193 Scroll up to view Page 116 - 120
121
Maintenance and Monitoring
This page provides some basic information about the current access point and a
real-time display of the transmit and receive statistics for this access point as described
in the following table. All transmit and receive statistics shown are totals since the access
point was last started. If the AP is rebooted, these figures indicate
transmit/receive totals since the reboot.
Field
Description
IP Address
IP Address
for the access point.
MAC Address
Media Access Control (
MAC
) address for the specified interface.
A MAC address is a permanent, unique hardware address for any device
that represents an interface to the network. The MAC address is
assigned by the manufacturer.
The D-Link DWL-2210AP has a unique MAC address for each interface. A
two-radio access point has a different MAC address for each interface on
each of its two radios.
VLAN ID
Virtual
LAN
(
VLAN
) ID.
A VLAN is a software-based, logical grouping of devices on a network
that allow them to act as if they are connected to a single physical
network, even though they may not be.
VLANs can be used to establish internal and guest networks on the
same access point.
SSID
Wireless network name. Also known as the
SSID
, this alphanumeric key
uniquely identifies a wireless local area network.
The SSID is set on the Basic Settings tab. (See “Provide Administrator
Password and Wireless Network Name” in this manual.)
Transmit and Receive Information
Total Packets
Indicates total packets sent (in Transmit table) or received (in Received
table) by this access point.
Total Bytes
Indicates total bytes sent (in Transmit table) or received (in Received table)
by this access point.
Errors
Indicates total errors related to sending and receiving data on this access
point.
Page 122 / 193
122
Maintenance and Monitoring
Associated Wireless Clients
To view the client stations associated with a particular access point, navigate to
Status > Associations
on the Administration Web pages for the access point you want
to monitor.
The associated stations are displayed along with information about packet traffic
transmitted and received for each station.
Link Integrity Monitoring
The D-Link DWL-2210AP provides
link integrity monitoring
to continually verify its
connection to each associated client (even when there is no data exchange occurring).
To do this, the AP sends data packets to clients every few seconds when no other traffic
is passing. This allows the access point to detect when a client goes out of range, even
during periods when no normal traffic is exchanged. The client connection drops off
the list of associated clients within 300 seconds of a client disappearing, even if they
do not
disassociate (but went out of range).
What is the Difference Between an Association and a Session?
An
association
describes a client connection to a particular access point. A
session
describes a client connection to the network. A client network connection can shift from
one clustered AP to another within the context of the same session. A client station can
roam between APs and maintain the session.
For information on monitoring
sessions
, see “Understanding Session Monitoring
Information” in this manual.
Page 123 / 193
123
Maintenance and Monitoring
Rebooting the Access Point
For maintenance purposes or as a troubleshooting measure, you can reboot the D-Link
DWL-2210AP as follows.
1. Click the
Advanced > Reboot
tab.
2. Click the
Reboot
button.
The AP reboots.
Page 124 / 193
124
Maintenance and Monitoring
Resetting the Configuration
If you are experiencing extreme problems with the D-Link DWL-2210AP and have tried
all other troubleshooting measures, use the
Reset Configuration
function. This will restore
factory defaults and clear all settings, including settings such as a new password or
wireless settings.
1. Click the
Advanced > Reset
tab.
2. Click the
Reset
button.
Factory defaults are restored.
Keep in mind that if you do reset the configuration from this page, you are
doing so for this access point only; not for other access points in the cluster.
For information on the factory default settings, see “Default Settings for the
D-Link DWL-2210AP” in this manual.
Page 125 / 193
125
Maintenance and Monitoring
Upgrading the Firmware
As new versions of the D-Link DWL-2210AP firmware become available, you can
upgrade the firmware on your devices to take advantages of new features and
enhancements.
To upgrade the firmware on a particular access point:
1. Navigate to
Advanced > Upgrade
on the Administration Web pages for that
access point.
You must do this per access point; you cannot upgrade firmware automatically
across the cluster. Keep in mind that a successful firmware upgrade restores the
access point configuration to the factory defaults. (See “Default Settings for the
D-Link DWL-2210AP” in this manual.)
2. If you know the path to the
New Firmware Image
file, enter it in the textbox.
Otherwise, click the
Browse
button and locate the firmware image file.
Information about the current firmware version is displayed and an option
to upgrade a new firmware image is provided.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top