Page 11 / 80
Scroll up to view Page 6 - 10
11
Using the Configuration Utility
To configure the DWL-1750, use a computer which is connected to the
DWL-1750 with an Ethernet cable (see the
Network Layout
diagram).
n
n
n
First, disable the
Access the Internet using a proxy server
function.
To disable this function, go to
Control Panel > Internet Options >
Connections > LAN Settings
and uncheck the enable box.
Start your Microsoft Internet Explorer web browser program.
Type the IP Address and HTTP port of the DWL-1750 (the default port
is 2000; the IP is
192.168.0.50) in the address field (http://
192.168.0.50:2000/) and press Enter. Make sure that the IP
Addresses of the DWL-1750 and your computer are in the same
subnet.
Page 12 / 80
12
Note:
if you have changed the default IP Address assigned to the DWL-1750, make
sure to enter the correct IP Address.
Home > Wizard
The
Home>Wizard
screen will appear.
Please refer to the
Quick Installation
Guide
for more infor-
mation regarding the
Setup Wizard.
After the connection is established, you will see the user identification window as shown.
Using the Configuration Utility (continued)
n
n
Type
admin
in the
User Name
field
Click
OK
Connect to 192.168.0.1
Page 13 / 80
13
Using the Configuration Utility (continued)
Home > Wireless
Apply-
Click
Apply
to save the changes
Keys 1-4-
Input up to 4 WEP keys; select the one you wish to use
SSID-
Service Set Identifier (SSID) is the name designated for a specific wire-
less local area network (WLAN). The SSID’s factory default setting is
default.
The SSID can be easily changed to connect to an existing
wireless network or to establish a new wireless network.
Channel-
6
is the default channel. All devices on the network must share the same
channel.
WEP-
Wired Equivalent Privacy (WEP) is a wireless security protocol for Wire-
less Local Area Networks (WLAN). WEP provides security by encrypt-
ing the data that is sent over the WLAN. Select
Enabled
or
Disabled.
Disabled
is the default setting.
(Note: If you enable encryption on the
DWL-1750 make sure to also enable encryption on all the wireless cli-
ents or wireless connection will not be established).
WEP
Encryption-
Select the level of encryption desired: 64-bit, or 128-bit
Key Type-
Select
HEX
or
ASCII
Hexadecimal
digits consist of the numbers 0-9 and the letters A-F
ASCII
(American Standard Code for Information Interchange) is a code for representing
English letters as numbers from 0-127
Passphrase-
Select HEX in the Key Type field and enter the passphrase here
Page 14 / 80
14
Using the Configuration Utility (continued)
Home > Mode > Central Dynamic IP Router
Select
Central Dynamic IP Router
if you are locating the router in a central
position to obtain an IP Address automatically from your ISP or corresponding
wireless network.
Most Cable Modem Users will select this option.
You may enter the
Host Name
here (optional)
Host Name-
Select
Disable
or
Enable.
NAPT
is a form of NAT; it provides
a type of firewall by hiding internal IP Addresses and it works
as an inbound virtual server, with IP based access control
NAPT-
Enter the wireless IP Address of the DWL-1750. The default
IP Address is 192.168.1.50
IP Address-
Enter the subnet mask. All devices on your network should
have the same subnet mask
Subnet Mask-
Click
Apply
if you have made any changes
Apply-
WAN - Ethernet
LAN - Wireless
Page 15 / 80
15
Using the Configuration Utility (continued)
Home > Mode > Central Static IP Router
Select
Central Static IP Router
mode if the DWL-1750 will be in a central
location. In this mode you will enter the Static IP Address that is provided to you
by your ISP.
WAN - Ethernet
LAN - Wireless
Enter the IP Address assigned by your ISP
IP Address-
All devices in the network must have the same Subnet Mask
Subnet Mask-
Click
Apply
if you have made any changes
Apply-
Enter the IP Address assigned by your ISP
IP Address-
All devices in the network must have the same Subnet Mask
Subnet Mask-
Your ISP will provide this information
ISP Gateway
Address-
Your ISP will provide this information
DNS
Server
Address-
NAPT-
Select
Disable
or
Enable.
NAPT
is a form of NAT; it provides
a type of firewall by hiding internal IP Addresses and it works
as an inbound virtual server, with IP based access control
19216811.live