Page 81 / 122
Scroll up to view Page 76 - 80
77
D-Link DSL-2770L User Manual
Section 3 - Configuration
Routing
Select this box to enable routing, then select which routing protocol
to use:
•.RIPv1
:
Protocol in which the IP address is routed through the
internet.
•.RIPv2
:
Enhanced version of RIPv1 with added features such
as Authentication, Routing Domain, Next Hop Forwarding, and
Subnet-mask Exchange.
This identifies the rule.
Enter in the IP of the specified network that you want to access using
the static route.
Enter in the subnet mask to be used for the specified network.
Enter in the gateway IP address for the specified network.
Enter in the amount of hops it will take to reach the specified network.
Note: In a transmission path, each link is terminated at a network device
such as a router or gateway. The number of hops equals the number
of routers or gateways that data must pass through before reaching
the destination.
Select this box to enable the rule.
RIP:
ID:
Destination:
Subnet Mask:
Gateway:
Hop:
Enable:
The Routing page allows you to specify custom routes that determine how data is moved around
your network. After modifying
any settings, click
Save.Settings
to save your changes.
Page 82 / 122
78
D-Link DSL-2770L User Manual
Section 3 - Configuration
IPv6 Firewall
Select whether to
•.Turn.IPv6.Filtering.OFF
•.Turn.IPv6.Filtering.ON.and.ALLOW.computers.listed.to.access.
the.network
(all computers not specified will be denied access)
•.Turn.IPv6.Filtering.ON.and.DENY.computers.listed.to.access.
the.network
(all computers not specified will be allowed access)
For each rule, tick the checkbox on the left to enable the rule.
Enter a name for the rule.
Select whether to have the rule active
Always
,
Never
, or according to
a schedule you have created. For more about creating schedules, refer
to page 85.
Enter the starting IP address of the traffic you want to filter.
Enter the ending IP address of the traffic you want to filter.
Enter which protocol you want to filter.
Enter the port range of the traffic you want to filter.
Configure IPv6
Filtering Below:
Name:
Schedule:
Source:
Dest:
Protocol:
Port Range:
This page lets you adjust the IPv6 firewall settings to control IPv6 traffic allowed in and out of your network. After modifying
any settings, click
Save.Settings
to save your changes.
Page 83 / 122
79
D-Link DSL-2770L User Manual
Section 3 - Configuration
Budget Quota
Tick this box to enable quotas.
Select which interface to apply the budget quota to.
Enter the period of time to apply the budget quota to. After the time
limit has passed, the quota will reset.
Tick this box to enable download quotas.
Set the maximum allowed download amount in megabytes for the
period of time specified in
Limit.Time
.
Tick this box to enable upload quotas.
Set the maximum allowed upload amount in megabytes for the period
of time specified in
Limit.Time
.
This shows your current received and transmitted traffic totals so far.
You can click the
Refresh
button to update the totals. Please note that
the totals update every three minutes.
Enable Limitation
Quota:
Select Interface:
Limit Time(Days):
Enable Download
Quota:
Download Quota:
Enable Upload
Quota:
Upload Quota:
Traffic Information:
This page lets you set quotas for how much traffic is allowed to pass through the network. This may be useful to control usage
if there is a bandwidth cap in place.
Page 84 / 122
80
D-Link DSL-2770L User Manual
Section 3 - Configuration
Password
This page will allow you to change the password used to log in to the web configuration interface.
Tools
To change the password, enter the current password, then the new
password you want to use, then enter it again to confirm it, then click
Apply.Settings
to save your changes.
Set the idle time in seconds that are allowed before the web
configuration interface automatically logs out the user.
Enables a challenge-response test to require users to type letters or
numbers from a distorted image displayed on the screen to prevent
online hackers and unauthorized users from gaining access to your
router’s network settings.
Current/
New/Confirm
Password:
Session Idle
Time Out:
Enable
CAPTCHA:
Page 85 / 122
81
D-Link DSL-2770L User Manual
Section 3 - Configuration
Use this option to save the current router configuration settings to a
file on the hard disk of the computer you are using. First, click the
Save
button. A file dialog will appear, allowing you to select a location and
file name for the settings.
Use this option to load previously saved router configuration
settings. First, use the
Browse
option to find a previously saved file of
configuration settings. Then, click the
Load
button to transfer those
settings to the router.
This option will restore all configuration settings back to the settings
that were in effect at the time the router was shipped from the factory.
Any settings that have not been saved will be lost, including any
rules that you have created. If you want to save the current router
configuration settings, use the
Save
button above.
Save Settings to
Local Hard Drive:
Load Settings
from Local Hard
Drive:
Restore to
Factory Default
Settings:
Save/Restore Settings
This section allows you to manage the router’s configuration settings, reboot the router, and restore the router to the factory
default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
19216811.live