1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DSL-2750B
    5. /
  5. 2
Page 6 / 95 Scroll up to view Page 1 - 5
6
DSL-2750B User Guide
Networking Requirements
The following system specifications are required for optimum performance of the Router via 10/100 Ethernet
or 802.11n/g wireless.
ETHERNET:
• Pentium® or equivalent class machines or higher
• Microsoft® Windows® (8, 7,Vista®, XP, 2000, ME, NT 4.0, 98 SE) Mac OS® X, or Linux installed
• 64 MB RAM (128 MB recommended)
• 10 MB of free hard drive space
• 10/100 Base-T Network Interface Card (NIC)
• Internet Explorer® 6.0, Firefox® 3.0, Safari® 3.0 or Chrome 2.0 or higher
WIRELESS:
• Pentium® or equivalent class or higher
• Microsoft® Windows® (8, 7,Vista®, XP, 2000) or Mac OS® X installed
• 64 MB RAM (128 MB recommended)
• 10 MB of free hard drive space
• Internet Explorer® 6.0, Firefox® 3.0, Safari® 3.0 or Chrome 2.0 or higher
• Available IEEE 802.11n/g wireless clients
Page 7 / 95
7
DSL-2750B User Guide
Hardware Features
LED Indicators
1
Power
A solid green light indicates the unit is powered on.
A red light indicates a malfunction.
2
Ethernet (1-4)
A solid light indicates a connection to an Ethernet-enabled computer
on ports 1-4. This LED blinks during
data transmission.
3
Wireless
A solid green light indicates the wireless function is operating correctly.
A flashing green light indicates wireless traffic is passing through the
router.
4
USB
A solid green light indicates a good connection to a USB device. This
light will blink during data transmission.
5
DSL
A solid light indicates the DSL is synchronized.
A flashing LED indicates the modem is attempting to synchronize with
the DSL provider.
6
Internet
A solid green light indicates that the modem has an IP address and is
connected to the Internet.
A red light indicates that the modem does not have an IP address or
authentication has failed.
No light indicates that an ADSL connection is not present or the
modem is in bridge mode.
This section explains the LED states and descriptions. LED indicators are used to verify the unit’s operation and
status.
1
DSL Port
Connect to an active telephone line (RJ-11).
2
LAN Ports (1-4)
Connect Ethernet devices such as computers, switches, and hubs.
3
USB Port
Connect a USB thumb drive or external hard drive and share files with
users on your network.
4
WLAN Button
Pressing this button to turn the Wireless feature on or off.
5
Reset Button
Pressing the Reset button for 10 seconds restores the modem to its
original factory default settings.
6
ON/OFF
Press this button to turn the unit on or off.
7
Power Receptor
Receptor for the supplied power adapter.
8
WPS Button
Press the WPS button located on the side to add your device to an
existing network or to create a new network.
Ports/Buttons
The following chart displays the Router’s connector types:
Page 8 / 95
8
DSL-2750B User Guide
Installation
This section will explain how to configure your computers to connect to the gateway, configure the gateway
to connect to the Internet, and set up your wireless clients.
DSL Filters/Microfilters
ADSL signals must be blocked from reaching each telephone, answering machine, fax machine, or any similar
conventional device. Failure to do so may degrade telephone voice quality and ADSL performance.
Install a microfilter if you desire to use the DSL-equipped line jack for telephone, answering machine, fax
machine or other telephone device connections. Microfilter installation requires no tools or telephone
rewiring. Just unplug the telephone device from the baseboard or wall mount and plug in a microfilter and
then plug in the telephone device.
You can purchase microfilters from your local electronics retailer, or contact the original provider of your DSL
equipment.
Configure your Computer
Follow the steps below to configure your computer to automatically receive its IP settings from the Gateway:
1.
Windows® 8 - Press the
Windows
key and then type
IP
. Click
Settings
on the right side and then click
View Network Connections
.
Windows® 7 - Click on
Start > Control Panel > Network and Internet > Network and Sharing Center.
Windows Vista® - Click on
Start > Control Panel > Network and Internet > Network and Sharing
Center > Manage Network Connections.
Windows® XP - Click on
Start > Control Panel > Network Connections.
Windows® 2000 - From the desktop, right-click
My Network Places > Properties.
2. Right-click on the
Local Area Connection
which represents your D-Link network adapter and select
Properties.
3. Highlight
Internet Protocol (TCP/IP)
or
Internet Protocol Version 4 (TCP /IPv4)
and click
Properties.
4.
In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio buttons labeled
Obtain an
IP address automatically
and
Obtain DNS server address automatically.
5. Click
OK
twice to save your settings.
Windows® 8/7/Vista®/XP/2000
Page 9 / 95
9
DSL-2750B User Guide
Below are instructions for configuring your Mac OS® X operating system
1.
In the Mac OS X Dock, click on the
System Preferences
icon.
2. Under
Internet & Network
, click
Network
.
In the
Show
menu, select
Built-in Ethernet
or Ethernet
(Depending on your Mac OS version.)
3. Click the
TCP/IP
tab.
4.
In the Configure menu, select
Using DHCP
.
5. Click
Apply Now and Save
if your computer prompts you to save changes.
Mac OS® X
If you want to assign a static IP address, please use the settings below:
• Your PC’s TCP/IP address:
192.168.1.x (where “x” is any number between 2 and 254)
• The Default Gateway’s IP address: 192.168.1.1
• Subnet mask: 255.255.255.0
• DNS server:192.168.1.1 (same IP as the Gateway) or supplied by Verizon
Page 10 / 95
10
DSL-2750B User Guide
Connect your Gateway
12VDC IN
POWER
ON/OFF
WLAN
RESET
USB
LAN4
DSL
LAN3
LAN2
LAN1
DSL-2750B Gateway
Desktop Computer
1.
Connect an RJ-11 (phone) cable from your wall phone jack to the DSL port on the back of the DSL-2750B gateway.
2. Connect an Ethernet cable from the LAN1 port on the back of the DSL-2750B to the Ethernet port on your
computer.
3.
Connect the supplied power adapter into the power receptor on the back of the DSL-2750B gateway to a power
outlet or a surge protector (recommended).
4.
Once you connect the power adapter, press the ON/OFF button on the back of the gateway to turn the unit on.

Rate

4 / 5 based on 1 vote.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top