D-Link DIR-862L Router Manual PDF (Setup & Configuration Guide)

Page 51 / 151 Scroll up to view Page 46 - 50

47

D-Link DIR-862L User Manual

The following parameters will be available for conﬁguration:

Wireless Band:

Displays the wireless band being conﬁg-

ured. In this option we ﬁnd that the fol-

lowing parameters will be regarding the

2.4 GHz band.

Enable Wireless:

Check the box to enable the wireless func-

tion. If you do not want to use wireless,

uncheck the box to disable all wireless

functions. Select the time frame that you

would like your wireless network enabled.

The schedule may be set to

Always

. Any

schedule you create will be available in

the drop-down menu. Click

New Schedule

to create a new schedule.

Wireless Network Name:

The Service Set Identiﬁer (SSID) is the name of your wireless network. Create a name using up to 32 characters. The

SSID is case-sensitive.

802.11 Mode:

Here the user can manually select the preferred frequency band to use for this wireless network.

Enable Auto Channel Scan:

The auto channel selection setting can be selected to allow this device to choose the channel with the least

amount of interference.

Wireless Channel:

By default the channel is set to 1. The channel can be changed to ﬁt the channel setting for an existing wireless net-

work or to customize the wireless network. If you enable

Auto Channel Selection

, this option will be greyed out.

Transmission Rate:

Select the transmit rate. It is strongly suggested to select

Best (Automatic)

for best performance.

Channel Width:

When using the 802.11n frequency band, the user has an option to choose between a 20MHz or 20/40MHz band-

width.

Visibility Status:

The Invisible option allows you to hide your wireless network. When this option is set to

Visible

, your wireless

network name is broadcasted to anyone within the range of your signal. If you are not using encryption then they

could connect to your network. When

Invisible

mode is enabled, you must enter the Wireless Network Name (SSID)

on the client manually to connect to the network.

Page 52 / 151

48

D-Link DIR-862L User Manual

By default the wireless security of this router will be disabled. In this

next option the user can enabled or disable wireless security for the

2.4 GHz frequency band. There are two types of encryption that can be

used: WEP or WPA/WPA2.

Wireless Security Mode: WEP

Wired Equivalent Privacy (WEP) is the most basic form of encryption that

can be used for wireless networks. Even though it is known as a ‘weak’

security method, it is better than no security at all. Older wireless adapt-

ers may only support WEP encryption and thus we still ﬁnd this encryp-

tion method used today.

The following parameters will be available for conﬁguration:

WEP Key Length:

Here the user can specify to either use a

64-bit or a 128-bit encrypted key.

Authentication:

Authentication is a process by which the

router veriﬁes the identity of a network

device that is attempting to join the wire-

less network. There are two types authen-

tication for this device when using WEP.

Open System

allows all wireless devices

to communicate with the router before

they are required to provide the encryp-

tion key needed to gain access to the

network.

Shared Key

requires any wire-

less device attempting to communicate

with the router to provide the encryption

key needed to access the network before

they are allowed to communicate with the

router.

WEP Key 1:

Enter the WEP key used here. For 64-bit keys you must enter 10 hex digits into each key box. For 128-bit keys you

must enter 26 hex digits into each key box. A hex digit is either a number from 0 to 9 or a letter from A to F. You

may also enter any text string into a WEP key box, in which case it will be converted into a hexadecimal key using

the ASCII values of the characters. A maximum of 5 text characters can be entered for 64-bit keys, and a maximum

of 13 characters for 128-bit keys.

Page 53 / 151

49

D-Link DIR-862L User Manual

Wireless Security Mode: WPA-Personal

Wi-Fi Protected Access (WPA) is the most advanced and up to date wire-

less encryption method used today. This is the recommended wireless

security option. WPA supports two authentication frameworks. Personal

(PSK) and Enterprise (EAP). Personal requires only the use of a pass-

phrase (Shared Secret) for security.

The following parameters will be available for conﬁguration:

WPA Mode:

WPA is the older standard; select this op-

tion if the clients that will be used with the

router only support the older standard.

WPA2 is the newer implementation of the

stronger IEEE 802.11i security standard.

With the

WPA2

option, the router tries

WPA2 ﬁrst, but falls back to WPA if the

client only supports WPA. With the

WPA2

Only

option, the router associates only

with clients that also support WPA2 secu-

rity.

Cipher Type:

Select the appropriate cipher type to use

here. Options to choose from are Temporal

Key Integrity Protocol (

TKIP

), Advanced

Encryption Standard (

AES

), and Both (

TKIP

and AES

).

Group Key Update Interval:

Enter the amount of time before the group

key used for broadcast and multicast data

is changed.

Pre-Shared Key:

Enter the shared secret used here. This

secret phrase needs to be the same on all

of the wireless clients for them to be able

to connect to the wireless network suc-

cessfully.

Page 54 / 151

50

D-Link DIR-862L User Manual

Wireless Security Mode: WPA-Personal

Wi-Fi Protected Access (WPA) is the most advanced and up to date wire-

less encryption method used today. This is the recommended wireless

security option. WPA supports two authentication frameworks. Personal

(PSK) and Enterprise (EAP). Personal requires only the use of a pass-

phrase (Shared Secret) for security.

The following parameters will be available for conﬁguration:

WPA Mode:

WPA is the older standard; select this op-

tion if the clients that will be used with the

router only support the older standard.

WPA2 is the newer implementation of the

stronger IEEE 802.11i security standard.

With the

WPA2

option, the router tries

WPA2 ﬁrst, but falls back to WPA if the

client only supports WPA. With the

WPA2

Only

option, the router associates only

with clients that also support WPA2 secu-

rity.

Cipher Type:

Select the appropriate cipher type to use

here. Options to choose from are Temporal

Key Integrity Protocol (

TKIP

), Advanced

Encryption Standard (

AES

), and Both (

TKIP

and AES

).

Group Key Update Interval:

Enter the amount of time before the group

key used for broadcast and multicast data

is changed.

RADIUS Server IP Address:

When the user chooses to use the EAP

authentication framework, the RADIUS

server’s IP address can be entered here.

RADIUS Server Port:

When the user chooses to use the EAP authentication framework, the RADIUS server’s port number can be entered

here.

RADIUS Server Shared

Secret:

Enter the shared secret used here. This secret phrase needs to be the same on all of the wireless clients for them to

be able to connect to the wireless network successfully.

Page 55 / 151

51

D-Link DIR-862L User Manual

The following parameters will be available for conﬁguration:

Wireless Band:

Displays the wireless band being conﬁg-

ured. In this option we ﬁnd that the fol-

lowing parameters will be regarding the 5

GHz band.

Enable Wireless:

Check the box to enable the wireless func-

tion. If you do not want to use wireless,

uncheck the box to disable all the wireless

functions. Select the time frame that you

would like your wireless network enabled.

The schedule may be set to

Always

. Any

schedule you create will be available in

the drop-down menu. Click

New Schedule

to create a new schedule.

Wireless Network Name:

The Service Set Identiﬁer (SSID) is the name of your wireless network. Create a name using up to 32 characters. The

SSID is case-sensitive.

802.11 Mode:

Here the user can manually select the preferred frequency band to use for this wireless network.

Enable Auto Channel Scan:

The auto channel selection setting can be selected to allow this device to choose the channel with the least

amount of interference.

Wireless Channel:

By default the channel is set to 36. The channel can be changed to ﬁt the channel setting for an existing wireless

network or to customize the wireless network. If you enable

Auto Channel Selection

, this option will be disabled.

Transmission Rate:

Select the transmit rate. It is strongly suggested to select

Best (Automatic)

for best performance.

Channel Width:

When using the 802.11n frequency band, the user has an option to choose between a 20 MHz, 20/40 MHz, or

20/40/80 MHz bandwidth.

Visibility Status:

The

Invisible

option allows you to hide your wireless network. When this option is set to

Visible

, your wireless

network name is broadcasted to anyone within the range of your signal. If you are not using encryption then they

could connect to your network. When Invisible mode is enabled, you must enter the Wireless Network Name (SSID)

on the client manually to connect to the network.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share