Page 76 / 158
Scroll up to view Page 71 - 75
72
D-Link DIR-850L User Manual
Section 3 - Configuration
The following parameters will be available for configuration:
6rd IPv6 Prefix:
Enter the 6rd IPv6 address and prefix value used
here.
IPv4 Address:
Enter the IPv4 address used here.
Mask Length:
Enter the IPv4 mask length used here.
Assigned IPv6 Prefix:
Displays the IPv6 assigned prefix value here.
6rd Border Relay IPv4
Address:
Enter the 6rd border relay IPv4 address used here.
IPv6 DNS Server:
Enter the primary DNS Server address used here.
The IPv6 Internet Connection Setup Wizard is complete.
Click on the
Connect
button to continue. Click on the
Prev
button to return to
the previous page. Click on the
Cancel
button to discard all the changes made
and return to the main page.
Tunneling.Connection.(6rd)
After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings.
Page 77 / 158
73
D-Link DIR-850L User Manual
Section 3 - Configuration
IPv6 Manual Setup
There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6), PPPoE,
IPv6 in IPv4 Tunnel, 6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet
Service Provider.
Note:
If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed
or disabled.
Auto Detection
Select
Auto.Detection
to have the router detect and automatically
configure your IPv6 setting from your ISP.
Page 78 / 158
74
D-Link DIR-850L User Manual
Section 3 - Configuration
Static IPv6
Select
Static.IPv6
from the drop-down menu.
Enter the address settings supplied by your Internet provider
(ISP).
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select
Stateful.(DHCPv6)
,
SLAAC.+.RDNSS
or
SLAAC.+.
Stateless.DHCPv6
.
Enter the start IPv6 Address for the DHCPv6 range for your
local computers.
Enter the end IPv6 Address for the DHCPv6 range for your
local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
WAN IPv6 Address
Settings:
LAN IPv6 Address:
LAN Link-Local Address:
Enable
Autoconfiguration:
Autoconfiguration Type:
IPv6 Address Range
Start:
IPv6 Address Range
End:
IPv6 Address Lifetime:
Page 79 / 158
75
D-Link DIR-850L User Manual
Section 3 - Configuration
Autoconfiguration
Select
Autoconfiguration.(Stateless/DHCPv6)
from the
drop-down menu.
Select either
Obtain.DNS.server.address.automatically
or
Use.the.following.DNS.Address
.
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select
Stateful.(DHCPv6)
,
SLAAC.+.RDNSS
or
SLAAC.+.
Stateless.DHCPv6
.
Enter the start IPv6 Address for the DHCPv6 range for your
local computers.
Enter the end IPv6 Address for the DHCPv6 range for your
local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
IPv6 DNS Settings:
Primary/Secondary DNS
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable
Autoconfiguration:
Autoconfiguration Type:
IPv6 Address Range
Start:
IPv6 Address Range
End:
IPv6 Address Lifetime:
Page 80 / 158
76
D-Link DIR-850L User Manual
Section 3 - Configuration
PPPoE
Select
PPPoE
from the drop-down menu.
Enter the PPPoE account settings supplied by your Internet
provider (ISP).
Select
Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select
Dynamic
.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the
next box.
Enter the ISP Service Name (optional).
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your specific ISP. 1492 is the default MTU.
Select either
Obtain.DNS.server.address.automatically
or
Use.
the.following.DNS.Address
.
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
My IPv6 Connection:
PPPoE:
Address Mode:
IP Address:
User Name:
Password:
Service Name:
Reconnection Mode:
Maximum Idle Time:
MTU:
IPv6 DNS Settings:
Primary/Secondary DNS
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconfiguration:
19216811.live