D-Link DI-704P Router Manual PDF (Setup & Configuration Guide)

Page 21 / 53 Scroll up to view Page 16 - 20

Near the bottom of the

MAC Address Control

window, the following pull-down

menu and button will help you to input the MAC address.

Select a specific client in the

“DHCP clients”

pull-down menu.

Click on the

“Copy to”

button to copy the MAC address of the DHCP client you

select to the ID selected in the

“ID”

pull-down menu.

Previous page and Next Page:

At the bottom of the

MAC Address Control

window you will find these two buttons. Use them to navigate between the several

pages of the

MAC Address Control

function.

ADVANCED > FIREWALL

Page 22 / 53

22

The

Firewall

enables you to control what packets are allowed to pass the

router.

Outbound filter

applies on all outbound packets. However,

Inbound

filter

applies on packets that are destined for Virtual Servers or DMZ host

only. You can select one of the two filtering policies:

1.

Allow

all to pass except those that match the specified rules

2.

Deny

all to pass except those that match the specified rules

You can specify 8 rules for inbound or outbound. For each rule, you can

define the following:

•

Source IP address

•

Source port address

•

Destination IP address

•

Destination port address

For source or destination IP address, you can define a single IP address

(e.g., 4.3.2.1) or a range of IP addresses (e.g., 4.3.2.1-4.3.2.254). An empty

fields implies all IP addresses.

For source or destination port, you can define a single port (e.g., 80) or a

range of ports (e.g., 1000-1999).

Each rule can be enabled or disabled individually.

Inbound Filter:

To enable

the

Inbound Packet Filter,

click the check box next to

Enable

in

the

Inbound Packet Filter

field.

Outbound Firewall:

(to access the Outbound Filter, click

Outbound

Firewall

at the bottom of the window.)

To enable the

Outbound Packet Filter

click the check box next to

Enable

in

the

Outbound Packet Filter

field.

Follow the same procedure as for the Inbound Firewall.

The IP addresses

that you input will be blocked from the port activity that you input (e.g.,

browsing the internet, receiving mail etc.)

After

Outbound Packet Filter

setting is configured, click the

Apply

button.

Page 23 / 53

ADVANCED > SNMP

In brief, SNMP, the Simple Network Management Protocol, is a protocol

designed to give a user the capability to remotely manage a computer

network by polling and setting terminal values and monitoring network

events.

To enable

SNMP

click the check box next to

Local or Remote

in the

Enable

SNMP

field.

Local:

allow manager to access this device through LAN port

Remote:

allow manager to access this device through WAN port

You can define:

Get Community:

The

Get community

field is the name of your network.

Your SNMP manager must have the same name in their

Get community

setting to get SNMP values from this device.

Set Community:

The

Set community

field is the name of your network.

Your SNMP manager must have the same name in their

Set community

setting to set this device’s SNMP values.

Click

Apply

if you have made any changes.

Page 24 / 53

24

ADVANCED > DDNS

Dynamic DNS

To host your server on a changing IP address, you have to use dynamic domain

name service (DDNS).

Anyone wishing to reach your host only needs to know the name of it. Dynamic DNS

will map the name of your host to your current IP address, which changes each time

you connect to your Internet service provider.

Before you enable

Dynamic DNS

, you need to register an account on one of these

Dynamic DNS servers that we list in the

provider

field.

To enable

Dynamic DNS

click the check box next to

Enable

in the

DDNS

field.

Next you can enter the appropriate information about your Dynamic DNS Server.

You have to define:

Provider

Host Name

Username/E-mail

Password/Key

You will get this information when you register an account on a Dynamic DNS

server.

Click

Apply

if you have made any changes.

Page 25 / 53

ADVANCED > ROUTING

Routing

allows you to determine which physical interface address to use for

outgoing IP data grams. If you have more than one router and subnet, you will need

to enable the routing table to allow packets to find the proper routing path and allow

different subnets to communicate with each other.

To enable the

Routing Table,

click the check box next to

Enable

in the related field.

You have to define:

Destination

Subnet Mask

Gateway

Hop: router’s position compared to this Device; if it is under this device, then input 2.

For example, if the host wanted to send an IP data gram to 192.168.3.88

(destination), it would use the above table to determine that it had to go via

192.168.1.33 (a gateway),

Each rule can be enabled or disabled individually.

After the

routing table

setting is configured, click

Apply

.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share