D-Link DI-634M Router Manual PDF (Setup & Configuration Guide)

Page 11 / 94 Scroll up to view Page 6 - 10

11

DI-634M User’s Manual

D-Link Systems, Inc.

Getting Started

Please remember that

D-Link Wireless 108G MIMO

devices are pre-conﬁgured to

connect together, right out of the box, with their default settings.

For a typical wireless setup at home (as shown above), please do the following:

You will need broadband Internet access (a Cable or DSL-subscriber line into

your home or ofﬁce)

Consult with your Cable or DSL provider for proper installation of the modem.

Connect the Cable or DSL modem to the DI-634M Wireless Broadband Router

(

see the printed Quick Installation Guide included with your router

).

If you are connecting a desktop computer to your network, install the D-Link

Air

Plus

Xtreme G

DWL-G520 wireless PCI adapter into an available PCI slot on

your desktop computer. You may also install the DWL-520+, or the DWL-520.

(See the printed Quick Installation Guide included with the network adapter.)

Install the D-Link DWL-G650M wireless Cardbus adapter into a laptop computer.

(

See the printed Quick Installation Guide included with the DWL-G650M.

)

Install the D-Link DFE-530TX+ adapter into a desktop computer. The four

Ethernet LAN ports of the DI-634M are Auto MDI/MDIX and will work with both

Straight-Through and Cross-Over cable. (

See the printed Quick Installation Guide

included with the DFE-530TX+.

)

Page 12 / 94

12

DI-634M User’s Manual

D-Link Systems, Inc.

Using the Conﬁguration Menu

Whenever you want to conﬁgure your DI-634M, you can access the Conﬁguration

Menu by opening the Web-browser and typing in the IP Address of the DI-634M. The

DI-634M’s default IP Address is shown below:



Open the Web browser.



Type in the

IP Address

of the Router (http://192.168.0.1).

Note:

if you have changed the default IP Address assigned to the DI-634M, make sure

to enter the correct IP Address.



Type

admin

in the

User Name

ﬁeld.



Leave the

Password

blank.



Click OK.

http://192.168.0.1

Page 13 / 94

13

DI-634M User’s Manual

D-Link Systems, Inc.

Using the Conﬁguration Menu

Wizard

The Home>Wizard screen will appear. Please refer to the

Quick Installation Guide

for

more information regarding the Setup Wizard.

These buttons appear on most of the conﬁguration screens in this section. Please

click on the appropriate button at the bottom of each screen after you have

made a

conﬁguration change.

Home

The Advanced tab provides the following conﬁguration options: Wizard, Wireless, WAN,

LAN, and DHCP.

Home > Wizard

Page 14 / 94

14

DI-634M User’s Manual

D-Link Systems, Inc.

Using the Conﬁguration Menu

Wireless

Service Set Identiﬁer (SSID) is the name designated for a

speciﬁc wireless local area network (WLAN). The SSID’s factory

default setting is

default

. The SSID can be easily changed to

connect to an existing wireless network or to establish a new

wireless network.

6

is the default channel. All devices on the network must

share the same channel. (Note: The wireless adapters will

automatically scan and match the wireless setting.)

By default Super G mode is

Disabled

. Super G is a group of

performance enhancement features that increase end user

application throughput in an 802.11g network. Super G is

backward compatible to standard 802.11g devices. For top

performance, all wireless devices on the network should be

Super G capable. Select either Disabled, Super G without

Turbo, Super G with Dynamic Turbo, or Super G with Static

Turbo.

Standard 802.11g support, no enhanced capabilities.

Home > Wireless

SSID:

Channel:

Super G Mode:

Disabled:

Page 15 / 94

15

DI-634M User’s Manual

D-Link Systems, Inc.

Using the Conﬁguration Menu

Capable of Packet Bursting, FastFrames, Compression, and

no Turbo mode.

Capable of Packet Bursting, FastFrames, Compression, and

Dynamic Turbo. This setting is backwards compatible with

non-Turbo (legacy) devices. Dynamic Turbo mode is only

enabled when all nodes on the wireless network is Super G

with Dynamic Turbo enabled.

Capable of Packet Bursting, FastFrames, Compression, and

Static Turbo. This setting is not backwards compatible with

non-Turbo (legacy) devices. Static turbo mode is always on

and is only enabled when all nodes on the wireless network is

Super G with Static Turbo enabled.

Choose

Enabled

to broadcast the SSID across the network.

All devices on a network must share the same SSID (Service

Set Identiﬁer) to establish communication. Choose

Disabled

if

you do not wish to broadcast the SSID over the network.

Select

Open System

or

WPA-PSK

authentication.

Wired Equivalent Privacy (WEP) is a wireless security protocol

for Wireless Local Area Networks (WLAN). WEP provides

security by encrypting the data that is sent over the WLAN.

Select

Enabled

or

Disabled

.

Disabled

is the default setting.

(Note: If you enable encryption on the DI-634M make sure to

also enable encryption on all the wireless clients or wireless

connection will not be established.)

Select the level of encryption desired: 64-bit, or 128-bit.

Select

HEX

or

ASCII

.

Input up to 4 WEP keys; select the one you wish to use.

Super G without

Turbo:

Super G with

Static Turbo:

Super G with

Dynamic Turbo:

SSID Broadcast:

Authentication:

Key Type:

WEP Encryption:

Keys 1-4:

WEP:

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share