xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

27

delete ipif

Syntax

delete ipif [<ipif_name 12> {ipv6address <ipv6networkaddr>} | all]

Description

Delete an interface or all the interfaces.

Note that the system interface can not be deleted. By using this command, a IPv6 address

can be deleted from the ipif.

Parameters

ipif_name

- Specifies the name of the IP interface.

all

- All ipif except the System IP interface will be deleted.

ipv6networkaddr

- Specifies the IPv6 network address.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To delete interface Intface_1:

DGS-3627:admin# delete ipif Intface_1

Command: delete ipif Intface_1

Success.

DGS-3627:admin#

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

28

6

BPDU TUNNELING COMMANDS

The BPDU Tunneling commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters)

in the following table.

Command

Parameters

config bpdu_tunnel

ports [<portlist> | all] type [tunnel {stp | gvrp} (1) | uplink | none]

show bpdu_tunnel

enable bpdu_tunnel

disable bpdu_tunnel

Each command is listed, in detail, in the following sections.

config bpdu_tunnel

Purpose

Used to config BPDU Tunneling ports setting.

Syntax

config bpdu_tunnel ports [<portlist> | all] type [tunnel {stp | gvrp} (1) | uplink | none]

Description

BPDU tunneling is used to tunnel layer 2 protocol packet.

This command is used to config BPDU Tunneling ports type

When the device is operated with QinQ enabled, DA will be replaced by the tunnel multicast

address, and the BPDU will be tagged with the tunnel VLAN based on the QinQ VLAN

configuration and the tunnel/uplink setting.

When the device is operated without QinQ enabled, the BPDU will have its DA replaced by

the tunnel multicast address and be transmitted out based on the VLAN configuration and the

tunnel/uplink setting.

The tunnel multicast address for STP BPDU is 01-05-5d-00-00-00.

The tunnel multicast address for GVRP BPDU is 01-05-5d-00-00-21.

Parameters

ports

- Specify the ports on which the BPDU Tunneling will be enabled or disabled.

type

- Specify the type on the ports.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To config BPDU_Tunneling tunnel ports:

DGS-3627:admin# config bpdu_tunneling ports 1-4 type tunnelstp

Command: config bpdu_tunneling ports 1-4 type tunnel stp

Success.

DGS-3627:admin#

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

29

show bpdu_tunnel

Purpose

Used to show BPDU Tunneling global state, tunnel destination MAC address and ports state.

Syntax

show bpdu_tunnel

Description

This command is used to show BPDU Tunneling global state, tunnel destination MAC

address and ports state.

Parameters

None.

Restrictions

None,

Example usage:

To show BPDU tunneling state of all ports:

DGS-3627:admin# show bpdu_tunnel

Command: show bpdu_tunnel

BPDU Tunnel

: Enabled

STP Tunnel Multicast Address

: 01-05-5d-00-00-00

STP Tunnel Ports

: 1,2

GVRP Tunnel Multicast Adrress

: 01-05-5d-00-00-21

GVRP Tunnel Port

: 5,6

Uplink Ports

: 3,4

DGS-3627:admin#

enable bpdu_tunnel

Purpose

Used to enable the BPDU Tunneling function.

Syntax

enable bpdu_tunnel

Description

Enable the BPDU Tunneling function.

By default, BPDU Tunneling is disable.

Parameters

None.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To enable the BPDU Tunneling function:

DGS-3627:admin# enable bpdu_tunnel

Command: enable bpdu_tunnel

Success.

DGS-3627:admin#

disable bpdu_tunnel

Purpose

Used to disable the BPDU Tunneling function.

Syntax

disable bpdu_tunnel

Description

Disable the BPDU Tunneling function.

Parameters

None.

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

30

disable bpdu_tunnel

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To disable the BPDU Tunneling function:

DGS-3627:admin# disable bpdu_tunnel

Command: disable bpdu_tunnel

Success.

DGS-3627:admin#

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

31

7

802.1X COMMANDS

The Switch implements the server-side of the IEEE 802.1X Port-based and MAC-based Network Access Control. This

mechanism is intended to allow only authorized users, or other network devices, access to network resources by

establishing criteria for each port on the Switch that a user or network device must meet before allowing that port to

forward or receive frames.

The 802.1X commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table.