D-Link DGS-3612 Router Manual PDF (Setup & Configuration Guide)

Page 606 / 757 Scroll up to view Page 601 - 605

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

602

debug ripng state

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To enable RIPng debug globally:

DGS-3627:admin# debug ripng state enable

Command: debug ripng state enable

Success.

DGS-3627:admin#

debug ripng show flag

Purpose

This command is used to display the RIPng debug flag setting.

Syntax

debug ripng show flag

Description

Used to display the RIPng debug flag setting.

Parameters

None.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To show the current RIPng debug flag setting:

DGS-3627:admin# debug ripng show flag

Command: debug ripng show flag

Current Enabled RIPng Flags:

Interface State Change

Packet Receiving

Packet Sending

Route

DGS-3627:admin#

debug ripng flag

Purpose

This command is used to enable or disable the RIPng debug flag .

Syntax

debug ripng flag [{interface | packet [all | rx | tx] | route}(1) | all] state [enable | disable]

Description

Used to enable or disable the RIPng debug flag.

Parameters

interface

- The state of the RIPng interface debug. The default setting is disabled.

packet

- See below:

all

- Set all packets with debug flags.

rx

- Set inbound packets with debug flag.

tx

- Set outbound packets with debug flag.

route

- The state of the RIPng route debug. The default setting is disabled.

all

- Set all debug flags.

state

- See below:

enable

- Enable the designated flags.

Page 607 / 757

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

603

debug ripng flag

disable

- Disable the designated flags.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To enable the ripng interface debug:

DGS-3627:admin# debug ripng interface state enable

Command: debug ripng interface state enable

Success.

DGS-3627:admin#

After enabling RIPng on an interface, the following information may appear when the interface state changes:

The RIPng interface System has changed the link state to down.

Page 608 / 757

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

604

78

ROUTING INFORMATION PROTOCOL (RIP) COMMANDS

The Routing Information Protocol (RIP) commands in the Command Line Interface (CLI) are listed (along with the

appropriate parameters) in the following table.

Command

Parameters

config rip

[ipif <ipif_name 12>|all] {authentication [ enable <password 16> | disable ] |

v2_only | v1_or_v2 | disable] | state [enable | disable]}

enable rip

disable rip

show rip

{ipif <ipif_name 12>}

Each command is listed, in detail, in the following sections.

config rip

Purpose

Used to configure RIP on the Switch.

Syntax

config rip [ipif <ipif_name 12>|all] {authentication [ enable <password 16> | disable ] |

v1_or_v2 | disable] | state [enable | disable]}

Description

This command is used to configure RIP on the Switch.

Parameters

<ipif_name 12>

−

The name of the IP interface.

all

– To configure all RIP receiving mode for all IP interfaces.

authentication [enable | disable]

−

Enables or disables authentication for RIP on the Switch.

•

−

Allows the specification of a case-sensitive password.

tx_mode

−

Determines how received RIP packets will be interpreted – as RIP version

V1 only

,

V2

Only

,

or

V1 Compatible (V1 and V2)

.

This entry specifies which version of the RIP protocol will be

used to transfer RIP packets. The disabled entry prevents the reception of RIP packets.

•

disable

−

Prevents the transmission of RIP packets.

•

v1_only

−

Specifies that only RIP v1 packets will be transmitted.

•

v1_compatible –

Specifies that only RIP v1 compatible packets will be transmitted.

•

v2_only

−

Specifies that only RIP v2 packets will be transmitted.

rx_mode

−

Determines how received RIP packets will be interpreted – as RIP version

V1 only, V2

Only

,

or

V1 or V2

.

This entry specifies which version of the RIP protocol will be used to receive

RIP packets. The

disable

entry prevents the reception of RIP packets.

•

v1_only

−

Specifies that only RIP v1 packets will be received.

•

v2_only

−

Specifies that only RIP v2 packets will be received.

•

v1_or_v2

−

Specifies that only RIP v1 or v2 packets will be received.

state [enable | disable]

−

Allows RIP to be enabled and disabled on the Switch.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To change the RIP receive mode for the IP interface System:

Page 609 / 757

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

605

DGS-3627:admin# config rip ipif System rx_mode v1_only

Command: config rip ipif System rx_mode v1_only

Success.

DGS-3627:admin#

enable rip

Purpose

Used to enable RIP.

Syntax

enable rip

Description

This command is used to enable RIP on the Switch.

Parameters

None.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example Usage:

To enable RIP:

DGS-3627:admin# enable rip

Command: enable rip

Success.

DGS-3627:admin#

disable rip

Purpose

Used to disable RIP.

Syntax

disable rip

Description

This command is used to disable RIP on the Switch.

Parameters

None.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example usage:

To disable RIP:

DGS-3627:admin# disable rip

Command: disable rip

Success.

DGS-3627:admin#

Page 610 / 757

xStack

®

DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual

606

show rip

Purpose

Used to display the RIP configuration and statistics for the Switch.

Syntax

show rip {ipif <ipif_name 12>}

Description

This command will display the RIP configuration and statistics for a given IP interface or for

all IP interfaces.

Parameters

ipif <ipif_name 12>

−

The name of the IP interface for which to display the RIP configuration

and settings. If this parameter is not specified, the

show rip

command will display the global

RIP configuration for the Switch.

Restrictions

None.

Example usage:

To display RIP configuration:

DGS-3627:admin# show rip

Command: show rip

RIP Global State : Disabled

RIP Interface Settings

Interface

IP Address

TX Mode

RX Mode

Authen-

State

tication

------------- ---------------- ---------- ------------- ---------- -----

System

10.90.90.90/8

Disabled

Total Entries : 1

DGS-3627:admin#

Example usage:

To display RIP configurations by IP interface:

DGS-3627:admin# show rip ipif System

Command: show rip ipif System

RIP Interface Settings

Interface Name: System

IP Address: 10.53.13.33/8 (Link Up)

Interface Metric: 1

Administrative State: Disabled

TX Mode: V2 Only

RX Mode: V1 or V2

Authentication: Disabled

Total Entries: 1

DGS-3627:admin#

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share