D-Link DGL-4500 Router Manual PDF (Setup & Configuration Guide)

Page 56 / 108 Scroll up to view Page 51 - 55

5±

D-Link DGL-4500 User Manual

Section ³ - Conﬁguration

This Wizard helps you add wireless devices to the wireless network.

The wizard will either display the wireless network settings to guide you through manual conﬁguration, prompt you to enter

the PIN for the device, or ask you to press the conﬁguration button on the device. If the device supports Wi-Fi Protected Setup

and has a conﬁguration button, you can add it to the network by pressing the conﬁguration button on the device and then

the on the router within 60 seconds. The status LED on the router will ﬂash three times if the device has been successfully

added to the network.

There are several ways to add a wireless device to your network. A “registrar” controls access to the wireless network. A

registrar only allows devices onto the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup

button on the device. The router acts as a registrar for the network, although other devices may act as a registrar as well.

Start the wizard.

Add Wireless

Station:

Add Wireless

Device Wizard:

Page 57 / 108

5²

D-Link DGL-4500 User Manual

Section ³ - Conﬁguration

To use the Universal Plug and Play (UPnP

™

)

feature click on

Enabled

. UPnP provides

compatibility with networking equipment, software

and peripherals.

Unchecking the box will not allow the DGL-4500 to

respond to pings. Blocking the Ping may provide

some extra security from hackers. Check the box

to allow the Internet port to be “pinged”.

You may set the port speed of the Internet port

to 10Mbps, 100Mbps, or auto. Some older cable

or DSL modems may require you to set the port

speed to 10Mbps.

Check the box to allow multicast trafﬁc to pass

through the router from the Internet.

UPnP Settings:

WAN Ping:

WAN Port Speed:

Multicast streams:

Advanced Network Settings

Page 58 / 108

5³

D-Link DGL-4500 User Manual

Section ³ - Conﬁguration

Enter a new password for the Administrator Login Name. The

administrator can make changes to the settings.

Enter the new password for the User login. If you login as the User,

you can only see the settings, but cannot change them.

Enter a name for the DGL-4500 router.

Enables a challenge-response test to require users to type letters or

numbers from a distorted image displayed on the screen to prevent

online hackers and unauthorized users from gaining access to your

router’s network settings.

Check this option to enable HTTPS server through remote

management.

Remote management allows the DGL-4500 to be conﬁgured from

the Internet by a web browser. A username and password is still

required to access the Web-Management interface. In general, only

a member of your network can browse the built-in web pages to

perform Administrator tasks. This feature enables you to perform

Administrator tasks from the remote (Internet) host.

The port number used to access the DGL-4500.

Example: http://x.x.x.x:8080 whereas x.x.x.x is the Internet

IP address

of the DGL-4500 and 8080 is the port used for the Web Management

interface.

This section will list any rules that are created. You may click the

Edit

icon to change the settings or enable/disable the rule, or click the

Delete

icon to remove the rule.

Admin Password:

User Password:

Gateway Name:

Enable Graphical

Authentication:

Enable HTTPS

Server:

Remote

Management:

Remote Admin Port:

Inbound Filter:

Administrator Settings

This page will allow you to change the Administrator and User passwords. You can also enable Remote Management.

There are two accounts that can access the management interface through the web browser. The accounts are admin

and user.

Admin

has read/write access while

User

has read-only access. User can only view the settings but cannot

make any changes. Only the admin account has the ability to change both admin and user account passwords.

Page 59 / 108

54

D-Link DGL-4500 User Manual

Section ³ - Conﬁguration

Time Settings

Select the Time Zone from the drop-down

menu.

To select Daylight Saving time manually, select

enabled or disabled, and enter a start date and

an end date for daylight saving time.

NTP is short for Network Time Protocol. NTP

synchronizes computer clock times in a network

of computers. Check this box to use a NTP

server. This will only connect to a server on the

Internet, not a local server.

Enter the NTP server or select one from the

drop-down menu.

To manually input the time, enter the values

in these ﬁelds for the Year, Month, Day, Hour,

Minute, and Second and then click

Set.Time

.

You can also click

Copy.Your.Computer’s.Time.

Settings

.

Time Zone:

Daylight Saving:

Enable NTP

Server:

NTP Server Used:

Manual:

The Time Conﬁguration option allows you to conﬁgure, update, and maintain the correct time on the internal system

clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also

be conﬁgured to automatically adjust the time when needed.

Page 60 / 108

55

D-Link DGL-4500 User Manual

Section ³ - Conﬁguration

SysLog

The Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs

to a SysLog server on your network.

Enable Logging to

SysLog Server:

SysLog Server IP

Address:

Check this box to send the router logs to a

SysLog Server.

The address of the SysLog server that will be

used to send the logs. You may also select

your computer from the drop-down menu (only

if receiving an IP address from the router via

DHCP).

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share