Page 71 / 131
Scroll up to view Page 66 - 70
Restart/Reset
Restarting the DFL-700
Follow these steps restart the DFL-700.
Step 1
. Choose if you want to do a quick or full restart.
Step 2
. Click
Restart Unit
and the unit will restart.
Restoring system settings to factory defaults
Use the following procedure to restore system settings to the values set at the factory.
This procedure will possibly change the DFL-700 firmware version to lower version if
it has
been upgraded.
This procedure deletes all of the changes that you have made to the DFL-700
configuration and reverts the system to its original configuration including resetting interface
addresses.
Follow these steps reset the DFL-700 to factory default.
Page 72 / 131
72
Step 1
. Under the
Tools
menu and the
Reset
section, click on the
Reset to Factory
Defaults
button.
Step 2
. Click
OK
in the dialog to reset the unit to factory default, or press
Cancel
to cancel.
You can restore your system settings by uploading a previously downloaded system
configurations file to the DFL-700 if a backup of the device has been done.
Page 73 / 131
Upgrade
The DFL-700’s
software, IDS
signatures and system
parameters are all
stored on a flash
memory card. The flash
memory card is re-
writable and re-readable.
Upgrade
Firmware
To upgrade the
firmware first download
the correct firmware
image from D-Link. After
having the newest
version of software,
please store it on the
hard disk, then connect
to the firewall’s WebUI,
enter
Upgrade
on the
Tools
menu, click
Browse
and choose the
file name of the newest
version of the firmware,
then click
Upload
firmware image
.
The updating process won’t overwrite the system configuration, so it is not necessary but still
a good idea to backup it before upgrading the software.
Upgrade IDS Signature-database
To upgrade the signature-database first download the newest IDS signatures from D-Link.
After having the newest version of software connect to the firewall’s WebUI, enter
Upgrade
on the
Tools
menu, click
Browse
in the
Upgrade Unit’s signature-database
section and
choose the file name of the newest version of the IDS signatures, then click
Upload
signature database
.
Page 74 / 131
74
Status
In this section, the DFL-700 displays the status information about the Firewall.
Administrator may use Status to check the System Status, Interface statistics, VPN,
connections and DHCP Servers.
System
Click on
Status
in the menu bar, and then click
System
below it. A window will appear
providing some information about the DFL-700.
Uptime
– The time
the firewall have been
running, since the last
reboot or start.
CPU Load
–
Percentage of cpu used.
Connections
–
Number of current
connections trough the
firewall.
Firmware version
–
The firmware version
running on the firewall.
Last restart
– The
reason for the last
restart.
IDS Signatures
–
The IDS signature
versions.
There are also two
graphs on this page,
one showing the CPU
usage during the last 24
hours. The other one is
showing the state table usage during the last 24 hours.
Page 75 / 131
Interfaces
Click on
Status
in the menu bar, and then click
Interfaces
below it. A window will appear
providing information about the interfaces in the DFL-700. By default information about the
LAN
interface will be show, to see another one click on that interface (
WAN
or
DMZ
).
Interface
– Name of
the interface shown,
LAN, WAN or DMZ.
Link status
–
Displays what link the
current interface has,
the speed can be 10 or
100 Mbps and the
duplex can be Half or
Full.
MAC Address
–
MAC address of the
interface.
Send rate
– Current
amount of traffic sent
trough the interface.
Receive rate
–
Current amount of traffic
received trough the
interface.
There are also two
graphs displaying the
send and receive rate
trough the interfaces
during the last 24 hours.
19216811.live