Page 66 / 145
Scroll up to view Page 61 - 65
66
DCS-6620G User’s Manual
D-Link Systems, Inc.
Record Snapshots to your FTP server with Motion Detection
1
5
2
4
3
6
John Smith
123.123.123.1
Snapshot
Next, click the
Mail & FTP
button under the
Advanced
tab to set the FTP server settings for the
DCS-6620G
.
In this window, enter the settings for the FTP server you wish to record to. Optionally, you can
enter settings for a secondary backup FTP server.
Local FTP server port:
The Default port is 21. To connect to an FTP server, it is
recommended that you do not change the port number unless
your camera is behind a router. If your camera is behind a
router, you can assign any port number to this field, but you
must enable port forwarding on the router. Please refer to your
router manual for more information on port forwarding.
1st FTP server:
If you are going to upload snapshots to an FTP server, you will
need to fill in the Domain name or IP address of your external
server name and IP address will vary
depending on the user.)
The following user settings must be correctly configured for
remote access.
1
2
Click
Mail & FTP
Page 67 / 145
67
DCS-6620G User’s Manual
D-Link Systems, Inc.
Record Snapshots to your FTP server with Motion Detection
1st FTP password:
Specify the password to access the external FTP server
(ex. 12345).
1st FTP remote folder:
Specify the destination folder in the external FTP server
(ex. snapshot).
Primary FTP passive
mode
:
Passive mode will allow access to an external FTP server if
your camera is behind a router protected by a firewall.
2nd FTP server:
Specify the Domain name or IP address of your second
external FTP server. This field is optional if you have already
filled in the information for the first FTP server.
2nd FTP user name:
Specify the user name to access your backup FTP
server.
2nd FTP password:
Specify the user password to your backup FTP server.
2nd FTP remote folder:
Specify the destination folder on your external backup FTP
server.
For detailed information about each setting, please refer to
Configuration > Advanced > Network
in the section titled “Using the
DCS-6620G
With an Internet Browser” (page 34). Click the apply
button when finished.
Secondary FTP passive
mode:
Passive mode will allow access to a second external FTP
server if your camera is behind a router protected by a
firewall.
1st FTP user name:
Specify the user name to access the external FTP server
(ex. John Smith).
3
4
5
6
Page 68 / 145
68
DCS-6620G User’s Manual
D-Link Systems, Inc.
Record Snapshots to your FTP server with Motion Detection
Next, click the
Applications
button under the
Tools
tab to set the application settings for the
DCS-6620G
.
In this window, follow the steps below to set the application settings for snapshots to be
recorded to an FTP site:
Select the weekdays you would like to record and enter the
“Snapshots begin” time
and “Snapshots end” time for the weekly
schedule, or select “All the time except
for the above schedule” if you want to enable full time snapshot recording.
Check “Event operation.”
Set the delay “before detecting next event” to avoid continuous false alarms
following the original event.
Set the delay to “take snapshots after event” to capture the direction of the moving
object.
Check the window name (in this case Lab).
Check “Upload snapshots while motion detected.”
Click “Send snapshots by FTP” and check “FTP put snapshots with date and time
suffix”
Click the “Apply” button to save the settings.
Click the apply button when finished. You are now able to record snapshots to your FTP server
when motion detection is triggered.
Click
Applications
Page 69 / 145
69
DCS-6620G User’s Manual
D-Link Systems, Inc.
Using IP surveillance Software
Using IP surveillance Software
Installing the IP surveillance Software
Before you begin installing this application software, the hardware system requirements must
be checked first. The minimum system requirements recommended for this application are
as follows:
Browser: Internet Explorer 5.x or above
CPU: Intel Pentium 4 2.4GHz or above
SDRAM: 128MB SDRAM
Hard Disk: 40GB
Display Chip: nVidia, TNT, TNT2, GeForce series with 64MB Display memory
ATI Radeon series with 128MB Display memory
Put the installation disk into your CD-ROM, and it will run automatically. If it does not, open
“My Computer” and double click on the CD-ROM icon. Next the installation menu will appear.
Click “Install Software”. The following window will appear.
Click
IP surveillance
Page 70 / 145
70
DCS-6620G User’s Manual
D-Link Systems, Inc.
Using IP surveillance Software
The “License Agreement” window below will appear. Please read the following license
agreement carefully. Click “Yes” to accept this agreement and proceed with the installation.
Click
Next
Click
Yes
Installing the IP surveillance Software
(continued)
19216811.live