Page 11 / 145 Scroll up to view Page 6 - 10
11
Installation Wizard (continued)
Please wait while the
InstallShield Wizard
prepares to install.
Click
Next
.
Click
Installation Wizard
Page 12 / 145
12
Select the Program folder
that Setup will add program
icons to. You may type a new
folder name, or select one
from the existing folders list.
Click
Next
.
Please wait while the
Installation
Wizard
is
installed.
Installation Wizard (continued)
The InstallShield will install in
the following folder. To install
into a different folder, click
Browse and select another
folder.
Click
Next
.
Page 13 / 145
13
Installation Wizard (continued)
To access the Installation Wizard
screen, click on the Installation
Wizard Icon on your desktop.
IMPORTANT:
A hardware reset of the Internet Camera may be required if the
Installation
Wizard
cannot find the camera. To accomplish this reset, lightly insert a paper
clip (or a similar sized tool) into the reset hole on the back of the camera (see
page 131 for the location of the reset
hole). The LED on the front of the camera
will begin blinking red and green. When it stops the blinking cycle continue to
hold in the reset button until a second cycle of blinking red and green lights
indicates a second reset cycle has completed. This will take approximately 5-7
seconds.
The opening Installation Wizard screen
will appear and
show a MAC address
of the
DCS-5300G
and an IP Address
(which may or may not be correct
depending on what you have your
DCS-5300G
connected to). If you have
a DHCP* server on your network,
there will be a valid IP Address
displayed here, indicated by a “Yes”
under the assigned column.
*A DHCP server is a device that
supplies IP Addresses to its clients that
are on the same network.
Installation is now complete.
Click
Finish
.
DCS-5300G
Page 14 / 145
14
Installation Wizard (continued)
You have now completed the Setup Wizard and are ready to use your
camera! You can also continue to the section titled “Installing IP
surveillance Software” to install the IP surveillance software before you
begin to use the DCS-5300G.
The
Installation Wizard
will now show a MAC address for the
DCS-5300G
and an IP address. This IP address may not be correct at this step in the
installation until you see “Yes” under the assigned column. The camera is now
automatically configured with an IP address consistent to the device it is
connected to.
After you click on the
Link
to Selected Devices
button,
Installation
Wizard
will automatically
open
your
Internet
browser to the IP Ad-
dress of the
DCS-5300G
in this example it is: http:/
/192.168.0.146. Your
DCS-5300G
may have a
different IP Address.
Click on the
Link to Selected
Devices
button.
Select the MAC address.
For more information regarding the functions of this screen, see the following
section titled “Installation Wizard Screen.”
DCS-5300G
192.168.0.146
Page 15 / 145
15
Installation Wizard Screen
The following options are available on the Installation Wizard screen by clicking
on the corresponding tab:
Search -
Click to search for any available
cameras to connect to the network.
Add -
Click to manually add a camera to
the network. A window will appear,
prompting you to enter the camera’s
IP address or domain name. A
second window will appear,
prompting you to enter the port
number.
Remove -
Click to remove the selected camera(s) from the network.
Uncheck All -
Click to uncheck all selected cameras.
Links to Selected Devices -
Click to link all selected devices to the network.
Setup -
On the initial Setup Screen you can
configure System and Date/Time
settings for each camera. Click
Next
to configure Network settings
for the camera.
System Settings -
Enter a Camera Name and create
a Root password for the camera.
Date/Time Settings -
Enter the Date and Time for each
camera. These settings can also be
configured on the
Tools > System
screen (page 56) when configuring
the camera via a Web browser.
DCS-5300G

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top