D-Link DCS-5220 Router Manual PDF (Setup & Configuration Guide)

Page 86 / 153 Scroll up to view Page 81 - 85

¶´

D-Link DCS-5±±0 User Manual

Section ² - Conﬁguration

The video channel selection area provides the IP addresses and location information of the connected

video channels for the user’s reference. You can select a video channel in this area and create a

schedule for it.

The Primary schedule consists of the day time-line, week time-line, begin time selector, end time selector,

and event mode settings.

The Secondary schedule consists of event mode settings.

The operation buttons allow the user to manipulate the edited schedule of the selected video channel.

The scheduler can be closed from here.

The Functionalities of Conﬁguration Components

The four main parts of the scheduler have been brieﬂy described above. The four parts will be described in detail in

the following section.

Video Channel Selection Area:

Primary Schedule:

Secondary Schedule:

Operation Buttons:

In this area you will select the video channel that you want to set a schedule for. Each video channel will display a

name, an IP address, and the location. Please note that when you switch between video channels in this area, the

changes in the schedule of the previous video channel will be saved automatically.

Video Channel Selection Area

Page 87 / 153

¶µ

D-Link DCS-5±±0 User Manual

Section ² - Conﬁguration

Primary Schedule

Schedule with Time Lines

There are two different time-lines: hour unit time-line and week unit time-line. You can make your own schedule by

plotting markers in all time-lines. These two time lines are associated with each other. That is, if you make changes in

one time-line, the corresponding changes will be applied with scale to the other three time-lines in the same schedule.

Before you begin, make sure that you select “Once” (page 85) if you want to choose the days to record on.

Week Time-Line

In the ﬁgure below, Week time-line is displayed. It includes the time-line, schedule information, and the selected day

in the week.

Marking/Unmarking the Recording Time on the Week Time-Line

The corresponding changes for the markers on the week time-line will be automatically added to the hour time-lines,

which is shown above. You can also mark and unmark the plotted bar by clicking and dragging with the left and the

right mouse button.

Hour Time-Line

In the ﬁgure below, the Hour time-line is displayed.

Page 88 / 153

¶¶

D-Link DCS-5±±0 User Manual

Section ² - Conﬁguration

There are three controlling units in both “Begin Time” and “End Time” selectors shown below. The ﬁrst unit of these two

selectors is the date picker. You can select day with it to set the beginning time and the ending time for the recording

interval.

The second and third units are the hour picker and the minute picker. You can change the hour and minute settings

for the beginning and ending time with them.

Note:

The time set in “Begin time” must be earlier than that in “End time”. Otherwise the settings will not be applied.

Marking/Unmarking the Recording Time on the Hour Time-Line

You can apply the one-click function by clicking the left mouse button and dragging to mark the time on this time-line.

The operating method for the hour time-line is the same as that of the week time-lines. Please refer to the previous

section about marking/unmarking on the week time-line for more details.

Schedule with Time Picker

Begin and End Time

Apply and Erase Buttons

After you have selected the time period with “Begin time” and “End time” picker, you can apply the period picker, shown

in the ﬁgure below, to set the periodical types of the time interval set previously. After the settings in “Begin Time”, “End

Time” and “Period Picker” are all done, you should click the “Apply” button or “Erase” button on the right to add or clear

this scheduling information to the editing schedule scheme. Note that only after you click on the “Apply” button, the

scheduling information settings will be written back into the whole editing schedule scheme. That means this edited

scheduling time interval is valid only after you “Apply” the changes.

Page 89 / 153

¶·

D-Link DCS-5±±0 User Manual

Section ² - Conﬁguration

Schedule in Event Mode

You can select to record in Event mode or Continuous mode by the Schedule mode selector as shown in the ﬁgure

below. There are two types of event recording. Please refer to the following two sections for more information.

Motion Detection

As shown below, you can check the windows that you would like to record while the motion detection is triggered.

Digital Input

In the ﬁgure below, there are four conditions for the digital input. Check the condition that you would like to record

while the condition triggers.

Note:

The Digital Input is not available for the DCS-5220 camera.

Page 90 / 153

·0

D-Link DCS-5±±0 User Manual

Section ² - Conﬁguration

Checking this will trigger recording while the digital input is high. The technical name for this event is

line trigger.

Checking this will trigger recording while the digital input is low. The technical name for this event is

line trigger.

Checking this will trigger recording while the digital input is changing from low to high. The technical

name for this event is edge trigger.

Checking this will trigger recording while the digital input is changing from high to low. The technical

name for this event is edge trigger.

High:

Low:

Rising:

Falling:

Schedule modes

If you select Continuous mode in the schedule mode selector, it will record continuously during the schedule that is

set up by the user.

Secondary Schedule

Secondary schedule is for recording outside of the primary schedule. The secondary schedule provides options to

record without a speciﬁed date or time.

Schedule in Continuous mode

There are three modes in the secondary schedule: Disable, Event mode, and Continuous mode. If event mode is

selected in the secondary schedule, the camera will record whenever an event is triggered. If continuous mode is

selected, the camera will begin recording continuously after scheduling settings are saved. These two modes are the

same as the primary schedule. Please refer to the previous section for more detail.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share