1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DCS-3220G
    5. /
  5. 2
Page 6 / 141 Scroll up to view Page 1 - 5
6
Connections
Ethernet Cable Connector
The
DCS-3220
back panel features an
RJ-45
connector for connections to
10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling. This network
port supports the
NWay protocol
, allowing the Internet Camera to automatically
detect or negotiate the transmission speed of the network.
.
DC Power Connector
The DC power input connector is located on the
DCS-3220
Internet Camera’s
back panel and is labeled
DC 12V
with a single socket to supply power to the
Internet Camera.
A reset to factory defaults will be initiated when the reset button is pressed
continuously for 5 seconds or when the Power LED changes from
green
to
red
for 2 cycles. (For example you will see the LED turn to
red
twice, release
the reset button when the LED turns red the second time). The Power LED
will begin to flash indicating that the Internet Camera’s settings are reverting
back to the factory settings, then turn back to
green
.
To reset the camera,
press the reset button once, and the LED will flash to
orange
.
The Ethernet cable included with the DCS-3220 Internet Camera is a
Category 5
“straight through” cable.
This is the recommended cable type
when the camera is connected to a 100 Mbps Fast Ethernet network hub or
switch.
Ethernet Cable Connector
DC Power Connector
I/O Connector
Reset Button
Audio Out Connector
Reset Button
Reset will be initiated when the reset button is pressed once and held until the
Power LED flashes through its cycle twice
Page 7 / 141
7
The
DCS-3220
provides a terminal block with two pairs of connectors situated
on the back panel. One pair is for input and the other is for output. The I/O
connectors provide the physical interface to send and receive digital signals to
a variety of external alarm devices.
Please refer to the appendix in this
manual for detailed information
.
Connections (continued)
Located on the bottom panel of the
DCS-3220
, the socket is used to connect
the camera stand to the Internet Camera by attaching the screw head on the
camera stand to the Internet Camera.
Bottom Panel
Socket for stand
Power LED
LED
stands for
L
ight-
E
mitting
D
iode.
The Power LED is positioned on the right side of the Internet Camera lens. As
soon as the power adapter is connected to the Internet camera the power LED
will flash
red
and
green
several times, the
DCS-3220
is conducting a
self-test. Upon passing the self-test the LED will turn
green
to indicate a good
connection to an Ethernet port or
red
to indicate no connection has been made.
I/O Connector
Attachment socket for the Camera Stand
Audio Out Connector
The
DCS-3220
provides an Audio Out connector to be used for 2-way audio.
Speakers (not included) may be connected to the camera to provide audio for
2-way conversations with those you are viewing.
Page 8 / 141
8
Hardware Installation
Connect an Ethernet cable
Connect an Ethernet cable to the network
cable connector located on the
DCS-3220
’s
back panel and attach it to the network.
Attach the external power supply
Attach the external power supply to the DC
power input connector located on the
DCS-3220
’s back panel labeled
12VDC
and connect the other end to your wall outlet.
The Internet Camera comes with a camera
stand with a swivel ball screw head that
can be attached to the Internet Camera
bottom socket cavity. Attach the camera
stand to the Internet Camera and station it
for your application. There are holes
located in the base of the camera stand
allowing the Internet Camera to be mounted
to the ceiling, or any wall securely.
Attaching the Internet Camera to the Camera Stand
When you have a proper connection, the LED will turn from
red
to
green
. The
light may cycle on and off and your computer may show an intermittent loss of
connectivity, this is normal until you have configured your Internet Camera.
Page 9 / 141
9
Installation Wizard
After you have successfully completed the hardware installation of the
DCS-
3220
Internet Camera, it is necessary to install software to configure and operate
the camera. The first step is to install the
Installation Wizard
from the CD.
Installation Wizard
will allow you to configure the Internet Camera to your
network
After the
Installation Wizard
software program is completed, you will have an
operating and controllable Internet Camera. From your Internet Explorer Web
browser you will be able to access the video and sound from the Internet camera.
The camera has a built-in Web server. This Web server will allow the camera to
access the Internet without being attached to a computer and permits users to
view the video and audio remotely.
After running the
Installation Wizard
, you will be able to operate the
DCS-3220
and view the camera remotely
through Internet Explorer 6.x or above.
However it is necessary to install the
IP surveillance
software from the enclosed
CD to create a truly powerful monitoring and surveillance system. The following
section will show in detail the installation of the
Installation Wizard
and the
IP
surveillance
software.
Installing the Installation Wizard program
Insert the CD that is included with the
DCS-
3220
Internet Camera
. The
DCS-3220
installation menu will start up automatically from the CD. If the CD
does not start up automatically (the Windows operating system can turn this
function off, for example), go to Start > Run > Type D:\Autorun (if D:\ is your
cd-rom drive) to access the installation menu shown below:
Click
Install Software
.
Page 10 / 141
10
Installation Wizard (continued)
Click
Installation Wizard
.
Please wait while the
InstallShield Wizard
prepares to install.
Click
Next
.

Rate

4 / 5 based on 1 vote.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top