D-Link DCS-1000W Router Manual PDF (Setup & Configuration Guide)

Page 1 / 8

1

Check Your Package Contents

These are the items included with your purchase:

If any of the below items are missing, please contact your reseller.

Before You Begin

You must have at least the following:

•

Web Browser

•

Wired Hub/Switch/Router OR Wireless 802.11b Router

•

CD-ROM Drive

DCS-1000W

D-Link 2.4Ghz Wireless

Internet Camera

This product can be set up using

any current Web browser, i.e.,

Internet Explorer 6.0 or

Netscape Navigator 7.0

•

One Internet Camera with 2 External Wireless

Antennas

•

One Installation CD-ROM (containing

Drivers, Installation Guide, Software, and

Manual)

•

Mounting Kit

•

One AC Power Adapter

•

One Category 5 Ethernet Cable

Page 2 / 8

2

Hardware Installation

System Requirements

•

Web Browser (Java Enabled recommended)

•

CPU: Pentium II, 266 MHz or above

•

Memory Size: 32 MB (64 MB recommended)

•

VGA card resolution: 800x600 or above

Connect the Ethernet Cable

Connect an Ethernet cable to the network cable connector

located on the DCS-1000W’s rear panel and attach it to

the network.

Note: We suggest using the Ethernet port to configure the

DCS-1000W, then installing the camera in its preferred

location. Doing so will allow easy installation and proper

configuration.

Attach the External Power Supply

Attach the external power supply to the DC power input

connector located on the rear panel of your camera and

connect it to your local power supply.

Note:

Power source

is confirmed when the blue LED Power Indicator on the

Internet Camera is illuminated. Network connection is

indicated by an orange LED.

Install Antennas

Locate the antenna connectors on the rear panel of your

DCS-1000W.

Attach the 2 external antennas that came with

the DCS-1000W into the antenna connectors.

Configure Network Communication

Locate the slide switch located on the rear panel of your

DCS-1000W.

Position the slide switch to either the LAN,

LAN+WLAN, or WLAN position depending on the type of

network configuration that you are planning to use with

your camera. Position the switch on LAN+WLAN if you

wish to connect to both your wired and wireless network.

Page 3 / 8

3

Running the Setup Wizard

You are now ready to run the Setup Wizard, which will guide you quickly through the

installation process.

Insert the

D-Link DCS-1000W

Driver CD

into your CD-ROM drive.

Click

Yes

Click

Install

Wizard

Page 4 / 8

4

Click

Finish

Click

Wizard

to begin

Your camera’s IP address will be displayed

here if it is valid.

To run the Setup Wizard, click on

Start

->

Programs

->

DCS-1000 Series Setup

Wizard

.

Running the Setup Wizard (continued)

Page 5 / 8

5

You must change the Admin ID and Pass-

word immediately to protect your camera

against unauthorized access. By default,

the Admin ID and Password are blank.

To

change the Admin ID and Password, select

both

Change

boxes and enter in a new

Admin ID and Password.

This screen appears if the default IP

Address of the camera (192.168.0.20) does

not correspond with your local area network

settings.

You must assign an IP address

for your camera that corresponds to your

network’s IP addressing scheme.

By default, the Admin ID and Password are

blank.

If you are running this Setup Wizard

for the first time, simply click OK to con-

tinue.

The IP Address of your camera must

corresond with your network settings for you

to access the camera.

If you are unsure of

what these settings should be, please

check with your network administrator.

Click

OK

Click

OK

Click

Yes

Click

169.254.60.196

D-Link DCS-1000W Router Manual PDF (Setup & Configuration Guide)

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share