Digisol DG-BR4000N Router Manual PDF (Setup & Configuration Guide)

Page 111 / 144 Scroll up to view Page 106 - 110

DG-BR4000NG User Manual

111

After you finish with all settings, please click ‘Apply’ button and the following

message will be displayed on your web browser:

If you want to reset all settings in this page back to previously-saved value, please

click ‘Cancel’ button

Please click ‘Continue’ to go back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take effect

(Please wait for about 30 seconds while the router is rebooting).

Page 112 / 144

DG-BR4000NG User Manual

112

3-2-5 UPnP Setting

This function enables network auto-configuration for peer-to-peer communications,

with this function, network devices will be able to communicate with other devices

directly, and learn information about other devices. Many network devices and

applications rely on

UPnP function nowadays.

Please click ‘UPnP’, menu on the left of web management interface, under the

‘NAT’ tab and the following message will be displayed on your web browser.

There are two options in this page, please select ‘Enable’ or ‘Disable’ to enable or

disable UPnP function, then click ‘Apply’ button, and the following message will be

displayed on your web browser:

If you want to reset all settings in this page, back to previously-saved value, please

click ‘Cancel’ button.

Please click ‘Continue’ to go back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take effect

(Please wait for about 30 seconds while router is rebooting).

Page 113 / 144

DG-BR4000NG User Manual

113

3-2-6 ALG Settings

Application Layer Gateway (ALG) is a special function of this router. It includes

many preset routing rules for numerous applications which require special support.

With these routing rules, those applications which required special support will be

able to work with NAT architecture.

Please click ‘ALG, menu on the left of web management interface, under the ‘NAT’

tab and the following message will be displayed on your web browser.

There are many applications listed here. Please check the box of the special support

for applications you need, and then click ‘Apply’ button and the following message

will be displayed on your web browser:

If you want to reset all settings in this page back to previously-saved value, please

click ‘Cancel’ button.

Please click ‘Continue’ to go back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take effect

(Please wait for about 30 seconds while router is rebooting).

Page 114 / 144

DG-BR4000NG User Manual

114

3-3 Firewall

Except NAT, this router also provides firewall function to block malicious intruders

from accessing your computers on local network. These functions include inbound

attack prevention, and block outbound traffics, like block URLs which have pre-

defined keywords.

Please follow the instructions mentioned below to enable or disable firewall

function:

Please click ‘General Setup’ menu on the left of web management interface, then

click ‘Firewall’ menu on the left of web management interface, and the following

message will be displayed on your web browser.

Please select ‘Enable’ or ‘Disable’ to enable or disable firewall function of this

router, then click ‘Apply’ button, and the following message will be displayed on

your web browser:

Please click ‘Continue’ to go back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take effect

(Please wait for about 30 seconds while router is rebooting).

Page 115 / 144

DG-BR4000NG User Manual

115

3-3-1 Access Control

This function allows or denies computers with specific MAC addresses from

connecting to the network; it can also allow or deny computers with specific IP

addresses, protocols, or ports. Please click ‘Access Control’ menu on the left of web

management interface, under the ‘Firewall’ tab and the following message will be

displayed on your web browser.

Here is the description of every setup item:

Parameter

Description

Enable MAC Filtering

Check this box to enable MAC address

based filtering, and please select ‘Deny’ or

‘Allow’ to decide the behavior of MAC

filtering table. If you select ‘Deny’, all

MAC addresses listed in filtering table will

be denied from connecting to the network;

if you select ‘Allow’, only MAC addresses

listed in filtering table will be able to

connect to the network, and rejecting all

other network devices.

Client PC MAC address

Please input the MAC address of the

computer or the network device here,

dash (-) or colon (:) are not required. (i.e.

If the MAC address label of your wireless

Rate

Popular Digisol Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share