Dell TrueMobile-2300 Router Manual PDF (Setup & Configuration Guide)

Page 171 / 178 Scroll up to view Page 166 - 170

Configuring your router for Wireless Bridging:

1. Open your web browser and go to

http://my.router

(or the default address

http://192.168.2.1

).

2. Click the

Advanced Settings

tab on the top navigation bar.

3. Click the

Advanced wireless

button on the left navigation bar.

4. Ensure

Enable Wireless

is checked.

5. Type your wireless network name in the

Network name (SSID)

field if you desire to change it from default

settings “Wireless”.

6. Ensure

Advanced Options

is unchecked.

7. Enable

Wireless Bridge

.

8. Enter the Wireless MAC address(es) of the other Dell TrueMobile 2300 Wireless Broadband Router(s) that

you want to bridge.

NOTE: To connect two bridges together, enter the MAC address of the bridge at the other end. To

connect three bridges together, enter the MAC addresses of the other two bridges in the bridge

acted as the multipoint center. The other two bridges only need to be entered the MAC address of

the center bridge.

9. Click the

Submit

button.

10. Click the

Save & Restart

button.

11. When your web browser returns to the main page of the Wireless Broadband Router, the device has

successfully restarted with the new settings.

Page 172 / 178

12. Repeat steps 1 to 11 for each Dell TrueMobile 2300 Wireless Broadband router you want to bridge.

NOTE: Ensure all Dell TrueMobile 2300 wireless Broadband Routers set to same wireless settings

and all router(s) not directly connected to Internet should be configured to Access point mode.

Back to Top

Parental Control

IP filtering is a mechanism enabling a networking node to accept or deny certain types of IP datagrams based on the IP

address, port number, protocol type, and other criteria. This router supports two types of IP filtering which allows you to have

greater control over the access to Internet:

Internet Access Control

allows you to block access to the Internet based on the time of the day.

Web Site Restrictions

allows you to deny access to specified Web sites from a particular IP address.

Click

Add

button. A pop-up

Parental Control Rule

window will appear.

Internet Access Control

1. Select the IP address of the particular computer you want to control (for example, your child's computer) in the

IP

Address

list.

2. To block / grant access to the Internet during a period of time, specify the start and end time from the

Time Restriction

list.

3. Select

Allow

or

Deny

from the

Internet Access

list.

4. Click the

SUBMIT

button to store the changes.

Web Site Restrictions

1. Enter the URL that you want to allow or deny the access in the

Web Site Restrictions

field.

2. Select

Allow

or

Deny

access to these web sites.

3. Click the

SUBMIT

button to store the changes.

Back to Top

Access Control Settings

Access Control Settings feature allows you to control which local client computer can access the network through the router.

The Wireless Broadband Router by default allows any local client computer to access the network.

To enable access control in the router:

1. Check the

Enable MAC Access Control

box.

2. Select the appropriate

Operating Type

.

Grant

allows client computers access to the router.

Deny

restricts the access.

3. Enter the MAC address of the network card on the computer on which you wish to apply the above control policy.

Page 173 / 178

4. Click

Add

to enter the rule to the router.

5. To remove an existing rule, check the "

Del

" checkbox next to the MAC address and click the

DEL

button.

6. Click the

SUBMIT

button to store the changes.

Back to Top

Port Forwarding Settings

DMZ

DMZ (demilitarized zone) feature allows access to all ports. (For example, if you have problems hosting a game server, you

can choose this option. This will open all ports to your game server.)

1. Check the

Enable DMZ Host

box.

2. Type the IP address of the computer that you want to run the gaming application in the

DMZ IP Address

field.

3. Click

SUBMIT

button to activate the setting.

NOTE: Configuring the Wireless Broadband Router in DMZ mode is useful if you want to play certain games through

the Wireless Broadband Router, but the ports cannot be opened with all other existing configuration tools.

NOTICE: Opening a service to the Internet causes security concerns. Pay careful attention to security alerts,

and make sure that strong access controls and authentication are in place before allowing access to any

services.

Custom Port Forwarding Settings

Port Forwarding may be more difficult than DMZ to configure. However, it provides a relatively safe way of running a Internet

application or providing a Internet service from behind a firewall since only a single port (or a range of ports) is exposed to the

Internet. You can configure this port forwarding setting to create a custom rule that defines a specific port and protocol for data

traffic to pass through to the specific computer on your LAN.

An example is a HTTP server running on your LAN, which you want it to be available to the Internet. Your public IP address

(that your ISP gives you) is X.X.X.X (The X is a number), and you have a computer hosting the HTTP server at LAN address

192.168.2.2 on your Wireless Broadband Router (192.168.2.1) controlled LAN. You can configure 192.168.2.2 to have port

forwarding for port 80 (HTTP), then users on the Internet can go to http://X.X.X.X and get the HTTP server (192.168.2.2). The

data traffic entering service port 80 will be directed to the computer (192.168.2.2), and other computers on your LAN will not

see this data traffic.

For some internet applications (such as Internet messaging and gaming applications), you can configure this port forwarding

setting so that these applications can function correctly behind the firewall. These applications are required to have specific

TCP/UDP ports.

The ports for these applications and the protocol type will depend on what Internet services you are using.

Please check with your service provider or application's user manual to have the information first.

Make sure you have the following ports setup as described below.

1. Check the

Enable

box.

2. Enter the desired name or description in the

Service Name

field.

3. In the

Incoming Ports

field, enter a range of ports. If you want to specify only a single port number, enter the same

number in both boxes.

Page 174 / 178

4. In the

Destination IP Address

field, enter the IP address of the computer you want to receive the connection request.

5. In the

Destination MAC Address

field, enter the MAC address of the computer you want to receive the connection

request.

Information

: Find the MAC address

The steps below show how to find the MAC address of the computer in Windows 2000 and XP.

a. Click on

Start

->

Run

.

b. Type

cmd

in the Open field and then press Enter or click OK button.

c. In the command prompt, type

ipconfig/all

to obtain the

Physical Address

(=MAC address).

d. Write down this Physical Address (=MAC address). You need this information for setting. Its format should

be XX-XX-XX-XX-XX-XX. The X is a hexadecimal digit (0-9 or A-F).

6. In the

Destination Port

field, enter a port number or a range of ports of the machine to which you are mapping.

7. In the

Port type

field, select TCP, UDP, or both protocols. The protocol could be specified in your application's

documentation.

8. Click

SUBMIT

button to activate the setting.

For example, if you want to play game "Fighter Ace II" on a computer with an IP address of 192.168.2.3, enter

3

for the

Destination IP Address

. Find the MAC address of this computer and enter it for the

Destination MAC Address

. Select

TCP

as the

Port type

. Enter "

50000

" and "

51000

" for two boxes of

Incoming Ports

and also for the

Destination Port

. Click

SUBMIT

button to activate the setting. For other games or services, please consult the application's user manual.

Commonly Used Ports

Services

Protocol Type

Ports

HTTP (WEB Server)

TCP

80

FTP

TCP

20, 21

TELNET

TCP

23

SMTP (Mail Server)

TCP

25

POP3 (Mail Server)

TCP

110

IRC

TCP

6667

NNTP (News Server)

TCP

119

Port Triggering

Port triggering allows the router to watch outgoing data for specific port number. The IP address of the the computer that

sends the data is remembered by the router, so that when the requested data returns through the router, the data will be

passed to the specific computer by way of IP address and port mapping rules. The router opens the port when the Port

Triggering happens. When the computer running the application stops sending the data through this port, the router will close

the port.

1. Check the

Enable

box.

2. Enter the desired name or description in the

Application Name

field.

3. In the

Trigger Port

field, enter a port number. Check with your Internet application provider for more information on

what the Trigger Port it is using.

4. Select TCP (Transmission Control Protocol), or UDP (User Datagram Protocol), or both protocols as the

Trigger Port

Type

.

Page 175 / 178

5. Specify the range of the

Public Ports

by entering the start and end port numbers in the required fields.

6. Select TCP (Transmission Control Protocol), or UDP (User Datagram Protocol), or both (TCP and UDP) as the

Public

Port Type

.

7. Click

SUBMIT

button to activate the setting.

Click the

SUBMIT

button to store the changes.

Back to Top

Static Routing

Static routes are manually configured routes to remote networks. That is, the route is predefined and is not discovered by the

Routing Information Protocol

(RIP), as in dynamic routing. Static routing allows you to assign a gateway to an IP address or

network. If there are routers on your internal network that do not function with RIP 1 or 2, you can set up a static route to those

routers.

The advantage to using static routing is that network traffic is reduced; thus, static routing is beneficial for slow Internet

connections. Routing using static routes is practical for small networks. For larger networks, the router needs to dynamically

keep track of changes in the physical wiring of the network, and the use of dynamic routing (RIP) is recommended.

NOTICE: The Static Routing settings are intended for advanced network administrators only. Do not change

these settings unless you are certain of the correct values. You may not be able to access the configuration

tool if invalid information is entered.

To use static routing, manually add the Destination IP Address, Subnet Mask, and Gateway IP Address for each route you are

adding to the Static Routing Table, and click

ADD

. If you are routing to an entire network, the last number in the destination IP

address should be a zero (0); for example, 192.168.0.0.

NOTE: In static routing, the Wireless Broadband Router does

NOT

dynamically discover routing information and does

NOT

use RIP. The Wireless Broadband Router currently does

NOT

support RIP.

Use the checkboxes beside each route and the

DELETE

button to remove static routes from the Static Routing Table.

Click the

SUBMIT

button to store the changes.

Back to Top

Administration Settings

Password Settings

The Wireless Broadband Router uses a password to authenticate the user before allowing changes to be made to

any network settings. If you would like to change the current password, check the

Change Your Password

checkbox and enter the new password in both

New Password

and

Retype Password

fields. Write down the

password and keep it in a secure location for future reference.

System Administration

HTTP Port No.

Do not change the

HTTP Port

value unless you have reason to do so. Typically, web servers listen for incoming

web requests on port 80.

Rate

Popular Dell Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share