1. Home
    2. /
  2. Manuals
    3. /
  3. Cisco
    4. /
  4. WRVS4400Nv2
    5. /
  5. 10
Page 46 / 180 Scroll up to view Page 41 - 45
WRVS4400N User Guide
40
Setup Tab
Setting Up and Configuring the Router
DHCP address range end—
Enter the ending DHCP v6 IP address.
Primary DNS
—Enter the Primary IPv6 DNS server address.
Secondary DNS
—Enter the Secondary IPv6 DNS server address.
Click the
Save Settings
button to save the network settings or click the
Cancel Changes
button to undo your changes.
DMZ
The
DMZ
screen allows one local PC to be exposed to the Internet for use of a special-purpose
service, such as Internet gaming and video-conferencing. DMZ hosting forwards traffic to all
the ports for the specified PC simultaneously, unlike Port Range Forwarding that can only
forward a maximum of 10 ranges of ports.
DMZ Hosting
—Allows one local PC to be exposed to the Internet for use of a special-purpose
service such as Internet gaming and video-conferencing. To use this feature, select
Enabled
. To
disable the DMZ feature, select
Disabled
.
DMZ Host IP Address
—To expose one PC, enter the computer’s IP address.
Click the
Save Settings
button to save the network settings or click the
Cancel Changes
button to undo your changes.
MAC Address Clone
Some ISPs require that you register a MAC address. This feature clones your PC network
adapter's MAC address onto the Router, and prevents you from having to call your ISP to
Downloaded from
www.Manualslib.com
manuals search engine
Page 47 / 180
WRVS4400N User Guide
41
Setup Tab
Setting Up and Configuring the Router
change the registered MAC address to the Router's MAC address. The Router's MAC address is a
6-byte hexadecimal number assigned to a unique piece of hardware for identification.
Mac Address Clone
—Select
Enabled
or
Disabled
. The default is Enabled.
Mac Address
—Enter the MAC Address registered with your ISP in this field.
Clone My PC’s MAC
button—When Mac Address Clone is enabled, click this button to copy the
MAC address of the network adapter in the computer that you are using to connect to the Web-
based utility.
Click
Save Settings
to save the MAC Cloning settings or click the
Cancel Changes
button to
undo your changes.
Downloaded from
www.Manualslib.com
manuals search engine
Page 48 / 180
WRVS4400N User Guide
42
Setup Tab
Setting Up and Configuring the Router
Advanced Routing
Operating Mode
Select the Operating mode in which the Router will function.
Gateway
—This is the normal mode of operation. This allows all devices on your LAN to share
the same WAN (Internet) IP address. In the Internet Gateway mode, the NAT (Network Address
Translation) mechanism is enabled.
Router
—You either need another Router to act as the Internet Gateway, or all PCs on your LAN
must be assigned (fixed) Internet IP addresses. In Intranet Router mode, the NAT mechanism is
disabled.
Dynamic Routing
The Router's dynamic routing feature can be used to automatically establish a routing table
through a database exchange with peer routers (running the same routing protocol). The
Router supports RIP (Routing Information Protocol) versions 1 & 2.
RIP (Routing Information Protocol—
The Router, using the RIP protocol, calculates the most
efficient route for the network’s data packets to travel between the source and the destination
based upon the shortest paths.
RIP Send Packet Version
—Choose the version of RIP packets you want to send to peers: RIPv1
or RIPv2. This should match the version supported by other Routers on your LAN.
RIP Recv Packet Version
—Choose the version of RIP packets you want to receive from peers:
RIPv1 or RIPv2. This should match the version supported by other Routers on your LAN.
Downloaded from
www.Manualslib.com
manuals search engine
Page 49 / 180
WRVS4400N User Guide
43
Setup Tab
Setting Up and Configuring the Router
Static Routing
Some ISPs require static routes to build your routing table instead of using dynamic routing
protocols. Static routes do not require CPU resources to exchange routing information with a
peer router. You can also use static routes to reach peer routers that do not support dynamic
routing protocols. Static routes can be used together with dynamic routes. Be careful not to
introduce routing loops in your network.
To set up static routing, you should add route entries in the routing table that tell the Router
where to forward packets to specific IP destinations.
Enter the following data to create a static route entry:
1.
Select Set Number
—Select the set number (routing table entry number) that you wish to
view or configure. If necessary, click
Delete This Entry
to clear the entry.
2.
Destination IP Address
—Enter the network address of the remote LAN segment. For a
standard Class C IP domain, the network address is the first three fields of the Destination
LAN IP; the last field should be zero.
3.
Subnet Mask
—Enter the Subnet Mask used on the destination LAN IP domain. For Class C
IP domains, the Subnet Mask is 255.255.255.0.
4.
Gateway—
If this Router is used to connect your network to the Internet, then your
gateway IP is the Router's IP Address. If you have another router handling your network's
Internet connection, enter the IP Address of that router instead.
5.
Hop Count (max. 15)
—Gives the number of routers that a data packet passes through
before reaching its destination. It is used to define the priority on which route to use if there
is a conflict between a static route and dynamic route.
Show Routing Table
button—Click this button to show the routing table established either
through dynamic or static routing methods.
Inter-VLAN Routing
Inter-VLAN Routing—
Select Enable to allow packets to be routed between VLANs that are in
different subnets. The default is Enable.
Downloaded from
www.Manualslib.com
manuals search engine
Page 50 / 180
WRVS4400N User Guide
44
Setup Tab
Setting Up and Configuring the Router
Click the
Save Settings
button to save the Routing settings, click the
Cancel Changes
button
to undo your changes or click the
Show Routing Table
button to view the current routing
table.
Time
You can either define your Router’s time manually or automatically through Time Server. The
default is
Automatically
.
Manually
Set the local time Manually—
If you wish to enter the time and date manually, select the
Date
from the drop-down fields and enter the hour, minutes, and seconds in the
Time
field using 24
hour format (example 10:00pm would be entered 22:0:0).
Automatically
Set the local time using Network Time Protocol (NTP) Automatically. If you wish to use a
Network Time Protocol server to set the time and date, select this option, then complete the
following fields.
Time Zone
—Select the time zone for your location and your setting synchronizes over the
Internet with public NTP (Network Time Protocol) Servers.
Auto Daylight Saving—
If your location observes daylight savings time, select the Enable
option.
User Defined NTP Server
—To use your own NTP server, select the
Enabled
option. The
default is Disabled.
NTP Server IP Address
—Enter the IP address of your own NTP server.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Popular Cisco Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top