Page 76 / 199 Scroll up to view Page 71 - 75
System Management
Setting Up Dual WAN and Multi-WAN Connections
Cisco Small Business RV0xx Series Routers Administration Guide
76
5
Interface Setting
Click the
Edit
icon for the interface that you want to set up. Then enter the settings
on the
Edit Dual WAN
settings page. For more information, see
Editing the Dual
WAN and Multi-WAN Settings, page 77
.
NOTE
If there are unsaved changes on the
Dual WAN
page, a warning appears. You can
click
OK
to close the message. Then click
Save
to save your changes. After saving
your changes, click the
Edit
icon. Alternatively, when the warning appears, click
Cancel
to continue to the edit page without saving the changes.
Page 77 / 199
Cisco Small Business RV0xx Series Routers Administration Guide
77
5
Editing the Dual WAN and Multi-WAN Settings
The
Dual WAN Settings
page (
Multi-WAN Settings
on RV016) appears after you
click the
Edit
icon for a WAN interface on the
Dual WAN
(or
Multi-WAN
) page. Enter
the interface settings, as needed.
NOTE
Before navigating away from this page, click
Save
to save your settings, or click
Cancel
to undo them. Any unsaved changes are abandoned.
Max Bandwidth Provided by ISP:
In this section, enter the maximum bandwidth settings as specified by your
Internet Service Provider. If the bandwidth exceeds the specified number, then the
router uses another WAN interface for the next connection.
Upstream:
Enter the maximum upstream bandwidth provided by your ISP.
The default is 512 kbit/sec.
Downstream:
Enter the maximum downstream bandwidth provided by
your ISP. The default is 512 kbit/sec.
Network Service Detection:
Optionally, check the box to allow the router to detect network connectivity by
pinging specified devices. Then enter the settings below. Uncheck the box to
disable this feature.
Retry count
: Enter the number of times to ping a device. The default is 5.
Retry timeout:
Enter the number of seconds to wait between pings. The
default is 30 seconds.
When Fail:
Choose the action that will be taken if a ping test fails. If you
choose
Generate the Error Condition in the System Log
, the router
Page 78 / 199
Cisco Small Business RV0xx Series Routers Administration Guide
78
5
records the failure in the System Log. There is no failover to the other
interface. If you choose
Remove the Connection
, failover occurs and the
backup interface is used. When the WAN port’s connectivity is restored, its
traffic is restored.
Default Gateway, ISP Host, Remote Host,
and
DNS Lookup Host:
Check
the box for each device that you want to ping to determine network
connectivity. For an ISP host or a remote host, enter the IP address. For a
DNS Lookup host, enter a host name or domain name. Uncheck a box if you
do not want to ping this device for network service detection.
Protocol Binding (for Cisco RV016 only, when Load Balancer is selected):
Use this feature to require this interface to be used for specified protocols and
specified source and destination addresses. If you enabled IP Group mode, this
feature is not available.
Add or update entries as needed. Remember that your entries are not saved until
you click the Save button.
To add a new entry to the list:
Enter the settings as described below, and
then click
Add to list
.
-
Service:
Choose a service (or All Traffic) to bind to this WAN interface. If
a service is not listed, you can click
Service Management
to add it. For
more information, see
Adding a service, page 79
.
-
Source IP
and
Destination IP:
Specify the internal sources and the
external destinations for the traffic that goes through this WAN port. For
a range of IP addresses, enter the first address in the first field and the
final address in the
To
field. For a single IP address, enter the same
address in both fields.
-
Enable:
Check the box to enable this rule, or uncheck the box to disable
it.
To add another entry to the list:
Enter the information, and then click
Add
to list
.
To modify an entry in the list:
Click the entry that you want to modify. The
information appears in the text fields. Make the changes, and then click
Update
. If you do not need to make changes, you can click
Add New
to de-
select the entry and clear the text fields.
Page 79 / 199
Cisco Small Business RV0xx Series Routers Administration Guide
79
5
To delete an entry from the list:
Click the entry that you want to delete, and
then click
Delete
. To select a block of entries, click the first entry, hold down
the
Shift
key, and then click the final entry in the block. To select individual
entries, press the
Ctrl
key while clicking each entry. To de-select an entry,
press the
Ctrl
key while clicking the entry.
Adding a service
To add a new entry to the
Service
list, or to change an entry that you created
previously, click
Service Management
. If the web browser displays a warning
about the pop-up window, allow the blocked content.
In the
Service Management
window, add or update entries as needed. Before
closing this window, click
OK
to save your settings, or click
Cancel
to undo them.
Any unsaved changes are abandoned.
To add a service to the list:
Enter the following information, and then click
Add to List
. You can have up to 30 services in the list.
-
Service Name:
Enter a short description.
-
Protocol:
Choose the required protocol. Refer to the documentation for
the service that you are hosting.
-
Port Range:
Enter the required port range.
Page 80 / 199
Cisco Small Business RV0xx Series Routers Administration Guide
80
5
-
To add another new service:
Enter the information, and then click
Add
to list
.
-
To modify a service you created:
Click the service in the list. The
information appears in the text fields. Make the changes, and then click
Update
. If you do not need to make changes, you can click
Add New
to
de-select the service and clear the text fields.
-
To delete a service from the list:
Click the entry that you want to delete.
To select a block of entries, click the first entry, hold down the
Shift
key,
and click the final entry in the block. To select individual entries, hold
down the
Ctrl
key while clicking. Click
Delete
.

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top