24
Setting Up: Advanced
Linksys E-Series
4.
6rd Tunnel
—Allows your router to send IPv6 IP addresses over IPv4
networks° To enable this option,
IPv6 - Automatic
must be set to
Disabled
° To let your router handle the 6rd Tunnel settings (such as
prefixes and address masks), change the 6rd Tunnel setting to
Automatic
Configuration
(default)° Select
Manual Configuration
to change these
settings manually°
•
Prefix
—Enter the prefix address used for the tunnel provided by your
ISP°
•
Prefix Length
—Enter the prefix length used for the tunnel provided
by your ISP°
•
Border Relay
—Enter the border relay address used for the tunnel
provided by your ISP°
•
IPv4 Address Mask
—Enter the IPv4 address mask length used for the
tunnel provided by your ISP°
5.
Click
Save Settings
at the bottom of the page°
How to get the most out of your dual-
band router
For
E2500
E3200
E4200
I bought a dual band router, but I’m not sure that I’m getting the most
out of it. What should I check?
Of the many reasons for owning a dual-band
router, the most common is to ensure available bandwidth for streaming high-
definition video° At the same time, owners want to make sure that their video
streams won’t be interrupted by other wireless network traffic° To get the most
out of your dual-band router, you can:
•
Upgrade your wireless clients
•
Split your traffic
Upgrade your wireless clients
If you have network adapters that support only legacy wireless network
standards such as 802°11b, you should consider upgrading them with
Wireless-N (802°11n) network adapters° Wireless-B (802°11b) devices can slow
your entire wireless network° For the best performance, all of your wireless
devices should support Wireless-N° You can then select
Wireless-N Only
as your
Network Mode below°
NOTE
If you select
Wireless-N Only
, you may need to temporarily change
your network settings to Mixed to provide access to guests without
Wireless-N networking°
Split your traffic
The best way to improve your multimedia wireless performance is to split your
wireless traffic between your router’s two bands (ranges of radio frequencies)°
Your router supports the 2°4 GHz band and the 5 GHz band, and handles the
two bands as two separate wireless networks to help manage the traffic°
The most common way to split wireless traffic is to use the 2°4 GHz band for
basic Internet tasks such as web browsing, email, and downloads, and use
the 5°0 GHz band for streaming multimedia° There are several reasons for this
approach:
•
Although the 2°4 GHz band may be more crowded with wireless traffic
from your neighbors, it’s fine for basic Internet traffic that is not time-
sensitive (such as e-mail)°
•
Even though you are connected to your own wireless network, you are
still sharing “air time” with nearby networks°
•
The 5 GHz band is much less crowded than the 2°4 GHz band, so it’s ideal
for streaming multimedia°
•
The 5 GHz band has more available channels, so it is more likely that you
will have your own, interference-free channel for your wireless network°
By default, your dual-band router uses the same network name on both the
2°4 GHz band and the 5 GHz band° If you are connecting to your router with
a computer that has a dual-band wireless network adapter, you might not be
able to determine which band you’re using° The easiest way to segment your
traffic is to rename one of your wireless networks° With a separate, descriptive
name, it will be easy to connect to the right network°
To reconfigure your wireless network:
Wireless > Basic Wireless Settings
1.
Log into the browser-based utility (see “How to open the browser-based
utility” on page 22)°
2.
Click the
Wireless
tab, then click the
Basic Wireless Settings
page°
3.
Click
Manual
° This enables you to make changes to all of the fields below°
19216811.live