1. Home
    2. /
  2. Manuals
    3. /
  3. CBN
    4. /
  4. CH7486E
    5. /
  5. 2
Page 6 / 44 Scroll up to view Page 1 - 5
6
Sample Wireless Network Connections (CH7486E model shown)
Your maximum wireless operation distance depends on the type of materials
through which the signal must pass and the location of your CH7486E and clients
(stations). CBN cannot guarantee wireless operation for all supported distances in
all environments.
Note: To get better wireless coverage, please put your
CH7486E wireless gateway VERTICALLY ONLY
Wired Ethernet LAN
You can easily connect any PC with an Ethernet cable to the CH7486E Ethernet
port. Because the CH7486E Ethernet port supports auto-MDIX
,
you can use a
straight- through or cross-over cable to connect a hub, switch, or computer. Use
category 5, or better, cabling for all Ethernet connections.
Page 7 / 44
7
Sample Ethernet to Computer Connection (CH7486E model shown)
A wired Ethernet LAN with more than two computers requires one or more hubs,
switches, or routers. You can:
Connect a hub or switch to any Ethernet port on the CH7486E.
Use Ethernet hubs, switches, or routers to connect up to any combination of
253 computers and wireless clients to the CH7486E.
More detailed information on Ethernet cabling is beyond the scope of this
document.
Page 8 / 44
8
Front Panel
The CH7486E front panel contains indicator lights and the Wi-Fi / WPS button
which is used to configure Wi-Fi Protected Security (WPS) on compatible clients
connected to the CH7486E network.
The CH7486E front panel LED indicators provide the following status information
for power, communications, and errors:
LED
Flashing
On
1
POWER
Not applicable
—
LED does
Green: Power is properly
Page 9 / 44
9
LED
Flashing
On
not flash
connected
2
ONLINE
Scanning for Internet
connection; transmitting or
receiving data over the
Internet
Green: Connected to Internet
3
WIRELESS
2.4GHz
5GHz
Amber: WPS function is
enabled.
Green: Wi-Fi wireless interface
is active now.
4
TEL 1/2
Telephone is off-hook;
dialing or call in progress
Green: Telephone is
connected and activated; on-
hook
Rear Panel
The CH7486E (shown above) rear panel contains the following cabling port and
connectors:
Page 10 / 44
10
Item
Description
1
PHONE
1
2
VoIP connection for a single telephone.
2
LAN
1
2 3
4
Use any Ethernet port to connect an Ethernet-equipped computer,
hub, bridge, or switch using an RJ-45 cable.
Activity LED - Green LED defines the activity of the Ethernet
connector.
When LED is ON, this indicates that there is no data traffic and a
connection is stabilized.
When LED is FLASHING, this indicates that there is data being
transmitted upstream or downstream.
When LED is OFF, this indicates that the unit is not powered or there
is no Ethernet connection.
3
RESET
Press and hold the RESET button for five seconds or longer to restore
CH7486E to factory default settings. After factory default settings
are restored, the gateway will restart and may take 5 to 30 minutes
to find and lock on the appropriate communication channels.
4
USB
USB host port for print server or network storage function
5
POWER
SWITCH
Switch gear for power on/off the CH7486E.
6
COAX
Connect the CH7486E to a cable wall outlet.
7
POWER
Provide power to the CH7486E.
MAC Label
The CH7486E Media Access Control (MAC) label is located on the bottom of the
CH7486E. The label contains the MAC address which is a unique, 48-bit value that
identifies each Ethernet network device. To receive data service, you will need to
provide the MAC address marked HFC MAC ID
to your Internet Service provider.”
Note: Label may differ according to local settings or requirements.

Rate

3.5 / 5 based on 2 votes.

Popular CBN Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top