Buffalo WZR-HP-AG300H-DD-WRT-v24SP2-MULTI Router Manual PDF (Setup & Configuration Guide)
Given below is full router user manual of Buffalo WZR-HP-AG300H-DD-WRT-v24SP2-MULTI router model. You can also download this manual in PDF Format to read later on your computer.
Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.
Page 1 / 171
User Manual for Professional Firmware
WZR-HP-AG300H
Nfiniti High Power Wireless Router & Access Point
www.buffalotech.com
35011803 ver.01
Page 2 / 171
1.
Introduction
3
1.1.
Welcome
3
1.2.
Device Configuration
3
1.2.1.
Factory Settings
3
1.2.2.
Initial Operation
3
2.
Configuration via the Web Interface
4
2.1.
Preparation
4
2.2.
Web Interface Access
4
2.3.
Web Interface Structure
5
2.3.1.
Setup
6
2.3.1.1.
Basic Configuration
6
2.3.1.2.
Dynamic DNS (DynDNS or DDNS)
6
2.3.1.3.
MAC Address Cloning
7
2.3.1.4.
Advanced Routing
7
2.3.1.5.
Networking
7
2.3.1.6.
EoIP Tunnel
8
2.3.2.
Wireless
8
2.3.2.1.
Basic Settings
8
2.3.2.2.
Wireless Security
10
2.3.2.3.
AOSS/WPS
11
2.3.2.4.
MAC Filter
12
2.3.3.
Services
12
2.3.3.1.
Services
12
2.3.3.2.
FreeRadius
12
2.3.3.3.
PPPoE Server
13
2.3.3.4.
VPN
13
2.3.3.5.
USB
13
2.3.3.6.
NAS
13
2.3.3.7.
Hotspot
14
2.3.3.8.
Milkfish SIP Router
14
2.3.3.9.
My Ad Network
14
2.3.4.
Security
14
2.3.4.1.
Firewall
14
2.3.4.2.
VPN Pass-through
14
2.3.5.
Access Restrictions
14
2.3.5.1.
WAN Access
14
2.3.6.
NAT / QoS
14
2.3.6.1.
Port Forwarding
14
2.3.6.2.
Port Range Forwarding
15
2.3.6.3.
Port Triggering
15
2.3.6.4.
UPnP
15
2.3.6.5.
DMZ
15
2.3.6.6.
QoS
15
2.3.7.
Administration
15
2.3.7.1.
Management
15
2.3.7.2.
Keep Alive
16
2.3.7.3.
Commands
16
2.3.7.4.
WOL
16
2.3.7.5.
Factory Defaults
16
2.3.7.6.
Firmware Upgrade
16
2.3.7.7.
Backup
16
2.3.8.
Status
16
2.3.8.1.
Router
16
2.3.8.2.
WAN
17
2.3.8.3.
LAN
17
2.3.8.4.
Wireless
17
2.3.8.5.
Bandwidth
17
- 1 -
Page 3 / 171
2.3.8.6.
SysInfo
17
3.
Use Cases
18
3.1.
Access Point
18
3.1.1.
Access Point with NAT / DHCP
18
3.1.1.
Access Point attached to a network / Internet gateway
19
3.2.
Wireless Client
20
3.3.
Wireless Client Bridge
21
3.4.
FTP Server
23
3.4.1.
Examples
23
3.4.2.
Logging into the FTP server
25
3.4.3.
Common FTP commands
25
4.
GPL Statement
27
4.1.
GNU General Public License
27
4.1.1.
Preamble
27
4.1.2.
GNU General Public License – Terms and Conditions or Copying,
Distribution and Modification
28
4.1.3.
NO WARRANTY
31
Appendix
Product Warranty Information
33
- 2 -
Page 4 / 171
1. Introduction
1.1. Welcome
This AirStation wireless router comes with two different firmware
packages. You may use either the dd-wrt-based Professional firmware or
the simple User-friendly firmware. By default, the Professional
firmware is preinstalled for US/EU products, and the User-friendly
firmware is preinstalled for Asia-Pacific products.
1.2. Device Configuration
From the factory, the router is configured as a network bridge. That
means that all network interfaces can communicate with each other
using this default bridge. The router is ready to use with a few
simple adjustments.
1.2.1.
Factory Settings
Because all interfaces are attached to the bridge by default, they all
have the same IP configuration:
IP address
192.168.11.1
Subnet Mask
255.255.255.0
DHCP server
enabled
DHCP-Range
192.168.11.2 - 66
The Wireless LAN interface is activated by default with an SSID
generated from the device’s MAC address. For security, unused
interfaces should be disabled. Wireless LAN interfaces that are not
disabled should be configured with secure encryption (WPA2 or WPA is
recommended) and a secure password.
1.2.2.
Initial Operation
Connect your computer to the router with an Ethernet LAN cable and
power the router on. It will take about 30 seconds to boot. You can
then access it via telnet or web browser at the IP address
192.168.11.1. The DHCP server in the router is enabled by default. If
your PC’s Ethernet is configured for DHCP it should receive an IP
address from the router’s DHCP server. If not, please configure the
Ethernet interface with an address from the 192.168.11.x subnet.
Because all relevant settings can be made using the web interface,
this manual refers to configuration via the web GUI only.
- 3 -
Page 5 / 171
2.
Configuration via the Web Interface
The router contains an integrated web server that provides an easy to
use web interface. It allows configuration, administration, and status
checking in a simple but effective way.
When accessing the web GUI for the first time, change the default
username and password. By default, the router’s status page can be
accessed without authentication, but this can be disabled.
The web interface was successfully tested on the following browsers:
-
Internet Explorer 7.x and newer versions
-
Firefox 2.x and newer versions
-
Safari 2.x and newer versions
2.1. Preparation
Connect your PC to the router and power the router on as described in
1.2.2. After the router has loaded its operating system, you can
communicate with it via your LAN network interface.
The easiest way to test if your PC can communicate with the router is
19216811.live