AVM FRITZ-Box-Fon-WLAN-7570 Router Manual PDF (Setup & Configuration Guide)

Page 56 / 159 Scroll up to view Page 51 - 55

FRITZ!Box Fon WLAN 7570 vDSL

56

Tips for Using USB Devices

8.8

Tips for Using USB Devices

USB Devices

When using USB devices at the USB port of the FRITZ!Box,

please keep in mind the following;

°

If more than one USB device without its own power

supply is connected to the FRITZ!Box, note that, in ac-

cordance with the USB specification, the total current

consumption may not exceed a value of 500 mA. Oth-

erwise unspecified malfunctions with the USB devices

or even damage to the FRITZ!Box may occur.

°

AVM expressly advises against installing firmware up-

dates for USB devices connected to the computer via

the USB remote connection on the FRITZ!Box.

USB Mass Storage

Devices

When using a USB storage device at the USB port of the

FRITZ!Box, please keep in mind the following:

°

Before removing the USB storage device, select the

“Remove Safely” button in the FRITZ!Box user inter-

face to prevent losses of data.

°

To avoid damage to the FRITZ!Box or the USB storage

device, operate USB storage devices that require more

than one USB port for operation (for instance hard

drives with a Y cable) only if they have their own power

supply or a USB hub with its own power supply.

°

AVM has no influence over external interference to the

USB storage devices on the FRITZ!Box. Thus such phe-

nomena as voltage spikes during storms may occur,

and writing to older USB memory devices may corrupt

the data structure due to a high number of defective

structures. In such cases a complete loss of data may

occur.

Therefore AVM recommends always making a security

copy of the USB memory content so that your data are

not irretrievably lost.

Page 57 / 159

Configuration and Operation at the Telephone

FRITZ!Box Fon WLAN 7570 vDSL

57

9

Configuration and Operation at the Telephone

FRITZ!Box Keypad Sequences

Many of the FRITZ!Box functions and features can be config-

ured and used over a telephone connected to a FRITZ!Box

extension. Only tone-dialing (dual-tone multifrequency =

DTMF) telephones can be used in configuration and opera-

tion. Pulse dialing telephones are not suitable.

Acknowledgment

Tone

Entries input on the telephone are confirmed with acknowl-

edgement tones (see also “Handset and Ring Patterns” on

page 113):

°

Entries made correctly are confirmed with a positive

acknowledgement tone (a single tone of one second

in length).

°

If the entry was not successful, because of an incor-

rect key sequence, for instance, you hear a negative

acknowledgment tone (an intermittent tone broken in-

to intervals of about 0.25 seconds).

9.1

Configuring at the Telephone

Saving New Settings

In this section, saving refers to

all

current settings made in

the FRITZ!Box. It is not necessary to save the configuration

immediately after every change. You may first configure all

of your settings as desired, and then save them permanent-

ly.

The telephone network features can be used only if they

are supported by your telephone network carrier and en-

abled on your telephone line.

Permanent saving cannot be reversed. However, you can

reprogram different settings or restore the FRITZ!Box to its

factory settings.

Page 58 / 159

FRITZ!Box Fon WLAN 7570 vDSL

58

Restoring Factory Settings

The FRITZ!Box can be reset to its condition upon delivery by

restoring factory settings.

After restoring factory settings, the FRITZ!Box is restarted.

Enabling/Disabling WLAN

The WLAN function can be switched on and off using the

telephone keypad. This is especially comfortable when the

WLAN function has been switched off. Simply use your tele-

phone to turn it back on. This means that the WLAN func-

tion can be enabled without having use a wired connection

to open the user interface.

Save Permanently

N

Pick up the handset.

r91ss

Save all settings permanently by dialing the

sequence shown at left.

O

Hang up the handset.

All settings you made in the FRITZ!Box—including the con-

figured Internet connection—are deleted when the factory

settings are restored.

Restore Factory Settings

r991s159

01590s

resets the FRITZ!Box to its condition upon

delivery

Enable/Disable WLAN

r96s1s

enables the WLAN function

r96s0s

disables the WLAN function

Page 59 / 159

Do Not Disturb

FRITZ!Box Fon WLAN 7570 vDSL

59

Do Not Disturb

You can enable the Do Not Disturb function for any tele-

phone connected to FRITZ!Box in the user interface. When

Do Not Disturb is enabled, the telephone will not ring. In

configuring this function you can choose between enabling

the function immediately and selecting a specific time peri-

od.

Immediately

When Do Not Disturb is enabled immediately, no incoming

calls will be signaled at the specified extension. The Do Not

Disturb setting will remain enabled until it is disabled.

Period

Alternatively, you can enter a Do Not Disturb period during

which the telephone will not ring. At the extension for

which a Do Not Disturb period is to be configured, define

the period during which the phone should not ring and

save your entries. Then enable Do Not Disturb. Do Not Dis-

turb then automatically will be switched on daily at the time

entered in the “Start” field and switched off again at the

time defined in the “End” field.

Example: Do Not Disturb should be configured from

08:00 p.m. until 07:00 a.m. daily. Enter the value “2000”

for <Start> and “0700” for <End>.

Disabling the

Function

Both kinds of Do Not Disturb settings can be disabled by

means of a keypad sequence.

Enable Do Not Disturb Effective Immediately

r81

<Ext.>

s0s

immediately enables Do Not Disturb for

the extension entered as <Ext.>

Enable Do Not Disturb for a Prescribed Period

r80

<Ext.>

s

<Start>

s

<End>

s

defines the period for Do Not Disturb at

extension <Ext.>

r91ss

saves the settings

r81

<Ext.>

s6s

enables Do Not Disturb for the defined pe-

riod

Page 60 / 159

FRITZ!Box Fon WLAN 7570 vDSL

60

Alarm

The FRITZ!Box includes an alarm function. The alarm can be

configured individually for each connected telephone.

First enter on the telephone the time at which you would

like to be awakened and save this entry. Then enable the

alarm function.

Example: The telephone should ring to wake you at

07:00 a.m. Enter the value “0700” as the <Time> and save

this setting.

Disable Do Not Disturb

r81

<Ext.>

s6s

disables Do Not Disturb for extension

<Ext.>

Configure the Alarm for a Telephone

r881s

<Time>

s

<Ext.>

s

defines for the extension <Ext.> the

time at which the telephone should

ring

r91ss

saves the settings

Enable/Disable the Alarm Function

r881ss

enables the alarm function for all ex-

tensions for which an alarm time was

set

r881r

disables the alarm function for all ex-

tensions

Rate

Popular AVM Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share