Page 26 / 72 Scroll up to view Page 21 - 25
26
4.2
LAN
4.2.1 LAN Settings
The LAN settings screen allows you to configure the local network
IP address of the LTE Router and modify the DHCP server settings.
To modify the LAN settings:
1. From the navigation panel, go to
Advanced Settings
>
LAN
>
LAN
tab.
2. Enter the IP address and subnet mask of the wireless router.
3. In the
Enable the DHCP Server
field, select
Yes
or
No
. By
default, the DHCP Server function is enabled.
4. In the
IP Pool Starting Address
field, key in the starting IP
address.
5. In the
IP Pool Ending Address
field, key in the ending IP
address.
Page 27 / 72
27
NOTES
:
We recommend that you use an IP address format of 192.168.1.xxx
(where xxx can be any number between 2 and 254) when specifying
an IP address range.
An IP Pool Starting Addressn should not be greater than the IP Pool
Ending Address.
6. In the
Lease Time
dropdown list, select the schedule when an
IP address will expire. Once it reaches this specified schedule,
the DHCP server will then assign a new IP address.
Static DHCP is a useful function, which allows you to bind specific
client device with static IP address on your LAN. The IP address on
DHCP server will be reserved for unique MAC address of a DHCP
client device based on the settings below.
Page 28 / 72
28
4.2.2 DHCP Client List
The DHCP Client List screen displays the DHCP client information.
Click
Refresh
to update the connected client list.
4.3
WAN
The LTE Router is implemented with an LTE (Long Term Evolution)
module. LTE network offers wide channel bandwidth from 5MHz
to 20 MHz, and fast mobile data rates of up to 50 Mbps uplink and
100 Mbps downlink.
The supported bands show as below:
LTE Band: FDD B3/7/20
• LTE Cat. 3: DL: 100Mbps, UL: 50Mbps
UMTS: B1/8
• HSPA +: DL: 42Mbps, UL: 5.76Mbps
4.3.1 Internet Connection
To configure the Internet Connection settings:
1. From the navigation panel, go to
Advanced Settings
>
WAN
>
Internet Connection
tab.
2. In the
WAN Type
field, select
LTE/UMTS
or
WAN
.
Page 29 / 72
29
WAN Type - LTE/UMTS
a. Set up the following:
PIN Code
: Enter the 3G/4G provider’s PIN code.
Connection Type
: This field allows you to define your
connection policies. We recommend you select
Auto-
Triggered by traffic
if you are not using all-you-can-eat data
service.
Location
: Select your 3G/4G service provider’s location from
the dropdown list.
APN services (optional)
: Enter the APN (Access Point
Name) service information here. Contact your 3G/4G service
provider for the detailed information.
Dial Number
: Enter the 3G/4G provider’s access number for
connection.
Page 30 / 72
30
Username / Password
: Enter the username and password
provided by the 3G/4G network carrier.
Dial on demand (with idle timeout timer)
: Enter the time
(in minutes) when the router goes into the sleep mode when
there is no activity in the network.
MTU
: Sets the MTU (Maximum Transmission Unit).
b. Click
Apply
to connect to the 3G/4G network. The connection
status will be displayed on
Mobile Connection Status
screen.
NOTE
: The PIN code may vary with different providers.
WAN Type - WAN

Rate

4 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top