1. Home
    2. /
  2. Manuals
    3. /
  3. Amped Wireless
    4. /
  4. R10000

Amped Wireless R10000 Router Manual PDF (Setup & Configuration Guide)

Given below is full router user manual of Amped Wireless R10000 router model. You can also download this manual in PDF Format to read later on your computer.

Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.

Page 1 / 2
1
2
Disconnect and Power Off your Existing Router
(If you have one)
Power Off your Modem
The Smart Setup Wizard will guide you
through the following settings:
Internet Connection Settings
System Clock
Wireless Settings
Click
Start
to begin.
1
2
3
8
Configure your Internet Connection
Configure your Internet settings using
the automatic settings.
More advanced users may choose to
configure their connection manually by
selecting Manual Configuration.
If your Internet provider requires that you
login before accessing the Internet you will
need to do so under Manual Configuration.
If the Automatic Configuration was successful,
you will be directed to a Configuration
Successful page.
Click
Next
to continue.
10
Configure your Wireless Settings
The default ID of your wireless network is:
Amped_Network
To change it, enter a new name in the SSID
field.
Users connecting wirelessly to the Router
will use this ID to identify your
wireless network.
Click
Next
to continue.
Set the System Clock
The System Clock is used for system logs
and setting schedules for Internet access.
Click
Sync
to synchronize the System Clock
with the time on your computer.
Click
Next
to continue.
9
If there was a problem with the Automatic
Configuration, the wizard will notify you of the
issue.
If you continue to have problems, contact
our support department at 888-573-8820.
— R E A D F I R S T —
SETUP GUIDE
High Power Wireless-N 600mW Smart Router
7
Welcome to the Smart Setup Wizard
Disconnect your existing router from your computer, your
broadband modem and its power outlet. If you do not have an
existing router please continue to Step 2.
Power off the Modem by disconnecting the Modem’s power
adapter from the power outlet. If your Modem has a backup
battery, remove the backup battery from your Modem.
Accessing the setup menu does not require Internet access.
The menu is served from the Router.
NOTE:
IF YOU HAVE PROBLEMS ACCESSING THE WEB MENU
Disable any third party firewalls that your computer may have on (i.e. Norton/Symantec/Windows).
Check to see that your computer is NOT connected to any wireless networks.
IF YOU HAVE PROBLEMS ACCESSING THE WEB MENU...
Need Help?
Give us a call.
Phone: 888-573-8820
Web: www.ampedwireless.com/support
?
R10000
Open your Web Browser
If the URL fails to open, then try: http://192.168.3.1
Enter the setup web address into your browser:
6
When prompted enter the login and password:
LOGIN:
admin
PASSWORD:
admin
Do NOT power on your Modem until Step 4.
5
Power On the High Power Router and Connect it to your Computer
Attach the two included Antennas.
Connect the included grey Ethernet cable to an
available network port on your computer.
Attach the Power Adapter to the the High Power
Router’s
port and a power outlet.
PWR
Modem
Remove
Backup battery
Existing Router
Modem
11
Wireless Security Settings
The default Security Key (WPA/WPA2) of your
wireless network is:
wireless
To change it, enter a new key in the Security Key
field.
The key must be at least 8 characters long.
Click
Next
t
o apply your settings.
The High
Power Router will reboot.
This process may take
up to 1 minute.
The page will automatically
reload after the countdown.
If it does not, you
may need to refresh the page manually or check
your connection to the router.
Congratulations, the High Power Router is now
successfully configured.
Your settings are now
saved.
You may now connect additional devices
directly to the 4 wired ports on the back panel,
or connect wirelessly to the High Power Router.
If you experience any problems at any point during the
Setup Wizard process, please contact Amped Wireless
Technical Support.
We’re here to help:
Phone:
888-573-8820
Email:
Web:
www.ampedwireless.com/support
12
Setup Summary
Modem
High Power Router
a
b
3
Connect the High Power Router to your Modem
Use the included blue Ethernet cable and
connect one end of the cable to your Modem.
Connect the other end of the cable to the blue
port on the High Power Router.
Modem
Do NOT connect the power adapter
to the High Power Router at this time.
4
Power on your Modem
Plug in the power adapter and reinsert the backup battery
(if available) to power on the Modem.
Allow a minute or two for the Modem to initiate.
Modem
Reinsert
Backup battery
Page 2 / 2
How to Connect Wirelessly to the High Power Router:
B. When prompted, enter the wireless
security key “
wireless
” and click
OK
.
A. Click on the Wireless icon to see available
wireless networks (For Vista, click Start >
Connect To).
Select the "
Amped_Network
"
network and click
Connect
.
Windows 7 and Vista
Troubleshooting Tips
I entered setup.ampedwireless.com and it failed to open the Web Menu.
a.
Make sure your computer is connected to the High Power Router using the included Ethernet cable.
Ensure that the power on the High Power Router is on.
b.
Check that your computer IS NOT connected to any wireless networks.
If it is, disable your WiFi connection
and disconnect from all wireless networks. Reboot the router and try again.
c.
Close your current web browser and reopen it.
Use Google Chrome or Internet Explorer (8.0 and up)
d.
Open your web browser and enter 192.168.3.1 into the web address bar.
e.
Reset the High Power Router to default settings by holding the Reset Button (located on the back panel) for
ten (10) seconds and try again
I am having problems with features on the Web Menu.
When clicking buttons, it does not register my action.
a.
Check that you are using a supported web browser:
Google Chrome, Internet Explorer (8.0 and up) and Safari.
If you are using an unsupported web browser, such as Firefox, please change to one of the supported web
browsers and try again.
I have a DSL connection and I am not able to access the Internet through the High Power Router
a.
Your Internet provider may require that you enter your login information to access the Internet.
To enter your
information, go to Manual Configuration from the Smart Setup Wizard and access the PPPoE menu from the
dropdown menu.
Enter the required login information for your Internet provider
The Smart Setup Wizard could not automatically configure my Internet connection.
a.
Reset your Modem by holding down the reset button located on the back of the Modem for approximately
5 seconds.
Try again.
b.
Reboot the High Power Router by unplugging the power adapter and plugging it back in.
c.
Static IP: Your Internet connection may require a static IP setting.
Check with your ISP to obtain the IP settings.
d.
DSL Connection: Your Internet connection may require login information.
If you are using PPPoE mode,
you will need to manually configure your Internet connection settings and obtain your username and password.
e.
Cable Modem:
Your Internet connection may require you to Clone your MAC address.
Go to More Settings >
IP Settings > Internet Network (WAN)
and select Automatic/Dynamic (DHCP) from the dropdown menu.
Clone your PCs MAC address under the DNS settings.
I am not getting maximum signal strength on my wireless signal display when connecting to the High Power Router
a.
Step back at least 10 feet from the High Power Router and check your signal again.
The High Power Router
emits high power, long range Wi-Fi signals that may confuse your wireless adapter signal reading at close
range.
The speed and signal are at 100%, however, your wireless network adapter readout may not be
displaying correctly.
b.
Change the wireless channel on the High Power Router to 11 or 1 and try again.
There may be wireless
interference in your installation environment.
My computer is getting an IP address of 169.254.x.x and/or Windows networking says I have “Limited or no
Connectivity”
a.
Make sure the High Power Router is powered on.
b.
Check that your computer’s network adapter is enabled and is set to “Obtain IP Address Automatically”
c.
Restart your computer and try again.
d.
You may have a faulty network port.
Try connecting to the High Power Router from another computer or
using the wireless connection on your computer, if possible.
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
Amped Wireless
A Division of Newo Corporation
Copyright © 2011 Amped Wireless / Newo Corporation.
All rights reserved.
Amped Wireless, Newo Corporation, the Amped Wireless Logo are registered trademarks or trademarks of Newo Corporation.
If you continue to have issues setting up the High Power Router, give us a call — we’re here to help: 888-573-8820
Visit our website for more support information and answers to frequently asked questions:
www.ampedwireless.com/support
LED Indicator Information
(From top to bottom)
Power:
Indicates when the High Power Router is powered on.
The LED will remain on.
Wireless Activity:
Blinks rapidly when wireless data traffic is transmitted or received over
the wireless network.
Internet Connection:
Indicates when the High Power Router is connected to a
broadband modem.
The LED will blink when Internet traffic is transmitted or received.
Wired Ports 1-4:
Indicates when a networking device is connected to a wired port on the
back of the High Power Router.
The LED blinks rapidly when wired data
traffic is transmitted or received.
WPS:
Wi-Fi Protected Setup activity.
When the WPS mode is activated, the WPS LED blinks
as it awaits a connection.
How to Reset the High Power Router to Default Settings
There are two options to reset the High Power Router back to factory default settings:
Hold down the Reset Button for five to ten (5-10) seconds.
You may need to use a pen tip or pin to
access the button.
Pressing the Reset Button for less than five (5) seconds will simply reboot the
High Power Router while saving your existing settings.
1
2
Access the Reset button through the web menu under
More Settings > Management >
Save/Reload Settings
on the left side of the web menu.
Select the
Reset Settings to Default.
Access the physical Reset Button on the back panel of the High Power Router:
Wi-Fi Protected Setup (One Touch Setup or Push Button Configuration)
If your Wi-Fi device has WPS one-touch setup you can use it to connect to the High Power Router:
Hold down the WPS button on the High Power Router (back panel) for 3 seconds.
The WPS LED will begin to blink.
As it blinks, push the WPS button on your wireless adapter or enable WPS with the provided
software for your wireless adapter.
WPS will automatically configure the connection settings
for your wireless adapter to connect to the High Power Router.
A.
B.
Using the Features on the High Power Router
The High Power Router is equipped with many powerful security features which can be accessed
through the web menu under
Smart Features, Firewall Settings
and
Quality of Service
on the left
side of the web menu:
If you are unfamiliar or want more information on how to setup Smart Features, Firewall
Settings, Quality of Service, please refer to the User’s Guide on the included CD.
12:26
Wireless Access Scheduling
Control when your Wi-Fi is on/off
Menu Location: Smart Features > Access Schedule
User Access Control
(Mac/IP)
Restrict network access to specific users
Menu Location: Smart Features > User Access
Wireless Coverage Control
Adjust the distance of your wireless network
Menu Location: Smart Features > Wireless Coverage
Block Websites
Prevent access to specific websites
Menu Location: Smart Features > Block Websites
Firewall Settings
Protect your network from outside intruders
Menu Location: Firewall Settings
Quality of Service (Prioritize Bandwidth)
Manage your network bandwidth
Menu Location: Quality of Service
Web Menu (Left Side)
www
www
This login/password is NOT the wireless network key used to connect to your wireless network.
LOGIN:
admin
PASSWORD:
admin
Setting a Login and Password
The High Power Router has a default login
and password to access the web menu:
It is strongly recommended that you change
these settings and select your own personal
login and password.
The Password menu can
be accessed through the web menu under
More Settings > Management > Password
on the left side of the web menu.
If you forget your login and password, you will need to reset the High Power Router back to default settings
and use the default login and password (login: admin, password: admin) to access the web menu.
View the
instructions below on how to reset your High Power Router back to default settings.
A. Tap the “Home” button to get to the home page.
B. Tap the “Settings” app icon.
C. Tap on Wi-Fi to enter the iPad’s Wi-Fi settings.
D. Touch the “On/Off” selector switch to “On”
E. Under “Choose a Network” select: “
Amped_Network
”
F.
When prompted, enter the wireless security key:
“
wireless
”
iPad Tablet
A. Tap the “Apps” menu on the tablet screen.
B. Locate and Tap the “Settings” app icon.
C. Under “Wireless & Networks” tap “Wi-Fi settings”
D. Tap the Wi-Fi box to turn on Wi-Fi and scan.
E. Under “Wi-Fi Networks” select: “
Amped_Network
”
F.
When prompted, enter the Password key: “
wireless
”
Android Tablet
B. When prompted, enter the wireless
security key “
wireless
” and click
OK
.
Mac OS X
A. Click on the Wireless icon to see available
wireless networks.
Select the "
Amped_Network
"
network and click
Connect
.
Amped_Network
Amped_Network
This is the second page of the Setup Guide.
Start on the opposite side first.
Wireless Network
Wireless Network
Amped_Network

Rate

4 / 5 based on 1 vote.

Popular Amped Wireless Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top