1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Telesis
    4. /
  4. AT-iMG624A
    5. /
  5. 36
Page 176 / 998 Scroll up to view Page 171 - 175
Switching
Switch command reference
iMG/RG Software Reference Manual (Switching)
2-26
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
2.2.4.1.30 SWITCH SET PORT QOS/NOQOS
Syntax
SWITCH SET PORT <portname> {QOS | NOQOS}
Description
This command enables/disables the 802.1p scheme priority on the selected switch port.
When 802.1p scheme priority is enabled, the 802.1p priority field value of each incoming
frame is compared with the switch base priority. If it is higher, the switch will forward the
frame to the high priority queue otherwise the frame will be forwarded to the low prior-
ity queue.
To change the switch base priority use the
SWITCH
SET
PRIORITY
command.
Options
The following table gives the range of values for each option which can be specified with
this command and a default value (if applicable).
Example
--> switch set port wan qos
See also
SWITCH SHOW PORT
SWITCH SET PRIORITY
2.2.4.1.31 SWITCH SET PORT RCVLIMIT
Syntax
SWITCH SET PORT <portname> RCVLIMIT < rcvlimit >
Option
Description
Default Value
port-name
The name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
mcastlimit
The maximum rate if ingress multicast traffic that will
be accepted on the switch port.
See Section 2.3 for a list of possible values - depend-
ing on product family.
none
Option
Description
Default Value
port-name
The name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
qos | noqos
When qos, the support of 802.1p IP field manage-
ment is active.
When noqos, any QoS policy based on 802.1p field
is disabled.
noqos
Page 177 / 998
Switch command reference
Switching
2-27
iMG/RG Software Reference Manual (Switching)
Description
This command specifies the ingress data rate limit. These limits apply to all frame types
entering on the selected switch port.
To show the current port status, use the SWITCH SHOW PORT command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> switch set port lan8 rcvlimit 4Mbps
2.2.4.1.32 SWITCH SET PORT RCVLIMIT-HIGH
Syntax
SWITCH SET PORT <portname> RCVLIMIT-HIGH < rcvlimit >
Description
This command specifies the ingress data rate limit for high priority traffic. These limits
apply to all frame types entering on the selected switch port that are high priority.
To show the current port status, use the SWITCH SHOW PORT command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> switch set port lan8 rcvlimit-high 4Mbps
2.2.4.1.33 SWITCH SET PORT RCVLIMIT-LOW
Syntax
SWITCH SET PORT <portname> RCVLIMIT-LOW < rcvlimit >
Option
Description
Default Value
port-name
The name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
rcvlimit
The maximum bit rate allowed on a switch port in
the receive direction. See Section 2.3 for a list of
possible values - depending on product family.
None
Option
Description
Default Value
port-name
The name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
rcvlimit
The maximum bit rate allowed on a switch port in
the receive direction. See Section 2.3 for a list of
possible values - depending on product family.
None
Page 178 / 998
Switching
Switch command reference
iMG/RG Software Reference Manual (Switching)
2-28
Description
This command specifies the ingress data rate limitfor the low priority traffic. These limits
apply to all frame types entering on the selected switch port that are categorized as low
prirority.
To show the current port status, use the SWITCH SHOW PORT command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> switch set port lan8 rcvlimit-low 4Mbps
2.2.4.1.34 SWITCH SET PORT SPEED
Syntax
SWITCH SET PORT <portname> SPEED <port-speed>
Description
This command set the speed value and mode on the selected switch port.
To show the current port status, use the SWITCH SHOW PORT command.
Options
The following table gives the range of values for each option which can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
port-name
The name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
rcvlimit
The maximum bit rate allowed on a switch port in
the receive direction. See Section 2.3 for a list of
possible values - depending on product family.
None
Option
Description
Default Value
Port-name
The name of the switch port to be configured. See
Section 2.3 for a list of possible port names.
N/A
port-speed
The port speed and mode. Allowed values are:
AUTO (Autonegotiate)
COAX (10Mbps Half Duplex)
10H (10Mbps Half Duplex)
10F (10Mbps Full Duplex)
100H (100Mbps Half Duplex)
100F (100Mbps Full Duplex)
1000H (1000Mbps Half Duplex)
1000F (1000Mbps Full Duplex)
AUTO
Page 179 / 998
Switch command reference
Switching
2-29
iMG/RG Software Reference Manual (Switching)
Example
--> switch set port lan1 speed 10F
See also
SWITCH SHOW PORT
2.2.4.1.35 SWITCH SET PORT STATUS
Syntax
SWITCH SET PORT <portname> STATUS { Enabled | Disabled }
Description
This command disables or enables the switch port.
To show the current port status, use the SWITCH SHOW PORT command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> switch set port lan1 status Disabled
2.2.4.1.36 SWITCH SET PORT TRSLIMIT
Syntax
SWITCH SET PORT <portname> TRSLIMIT < trslimit >
Description
This command specifies the ingress data rate limit. These limits apply to all frame types
entering on the selected switch port.
To show the current port status, use the SWITCH SHOW PORT command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> switch set port lan1 trslimit 8Mbps
Option
Description
Default Value
portname
he name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
Enabled | Disabled
When Enabled, the link is up and traffic can be sent
or received to/from the switch port.
When Disabled, the link is forced to be down.
Enabled
Option
Description
Default Value
portname
he name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
trslimit
The maximum bit rate allowed on a switch port in
the transmit direction. See Section 2.3 for a list of
possible values - depending on product family.
None
Page 180 / 998
Switching
Switch command reference
iMG/RG Software Reference Manual (Switching)
2-30
2.2.4.1.37 SWITCH SET PORT TRSLIMIT-HIGH
Syntax
SWITCH SET PORT <portname> TRSLIMIT-HIGH < trslimit >
Description
This command specifies the ingress data rate limit for high priority packets. These limits
apply to all frame types entering on the selected switch port that are high priority.
To show the current port status, use the SWITCH SHOW PORT command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> switch set port lan1 trslimit-high 8Mbps
2.2.4.1.38 SWITCH SET PORT TRSLIMIT-LOW
Syntax
SWITCH SET PORT <portname> TRSLIMIT-LOW < trslimit >
Description
This command specifies the ingress data rate limit for low priority packets. These limits
apply to all frame types entering on the selected switch port that are low priority.
To show the current port status, use the SWITCH SHOW PORT command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> switch set port lan1 trslimit-low 8Mbps
2.2.4.1.39 SWITCH SET PRIORITY
Syntax
SWITCH SET PRIORITY <802.1p_base_priority>
Option
Description
Default Value
portname
he name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
trslimit
The maximum bit rate allowed on a switch port in
the transmit direction. See Section 2.3 for a list of
possible values - depending on product family.
None
Option
Description
Default Value
portname
he name of the switch port to be configured.
See Section 2.3 for a list of possible port names.
N/A
trslimit
The maximum bit rate allowed on a switch port in
the transmit direction. See Section 2.3 for a list of
possible values - depending on product family.
None

Rate

4 / 5 based on 3 votes.

Popular Allied-Telesis Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top