Page 196 / 210 Scroll up to view Page 191 - 195
Section 5, DLP-021
NetVanta 2000 Series System Manual
196
© 2002 ADTRAN, Inc.
61200361L1-1E
DLP-021
Perform Steps Below in the Order Listed - Software Default
1.
Log in to the NetVanta 2000 series as
admin
(see DLP-001 for details).
2.
From the main menu (located across the top of the screen), select
A
DMIN
. This displays the
C
HANGE
P
ASSWORD
dialog box.
Performing a factory default using software will restore ALL configurable
parameters of the NetVanta 2000 series to factory conditions. All modified interface
address will be lost and may disrupt communications with the unit.
Page 197 / 210
NetVanta 2000 Series System Manual
Section 5, DLP-021
61200361L1-1E
© 2002 ADTRAN, Inc.
197
3.
From the menu list (located on the left side of the screen) select
F
ACTORY
D
EFAULT
.
4.
Click the Yes button to submit the operation. This will display the Reboot Confirmation screen.
Page 198 / 210
Section 5, DLP-021
NetVanta 2000 Series System Manual
198
© 2002 ADTRAN, Inc.
61200361L1-1E
5.
Click Yes to reboot the NetVanta 2000 series and restore all parameters to factory default settings.
6.
Complete the steps in
DLP-001 to access the
NetVanta 2000 series
unit.
Perform Steps Below in the Order Listed - Hardware Default
1.
Make sure the NetVanta 2000 series unit is powered up.
2.
On the rear panel of the NetVanta 2000 series unit there is a factory default pinhole located between
the LAN and WAN interfaces. Push the factory default pinhole for 1-2 seconds to restore the LAN
interface factory settings.
Follow-up Procedures
Once this procedure is complete, return to the procedure which referred you to this DLP and continue with
the tasks indicated there.
Performing a factory default using hardware only restores the LAN interface
parameters to default state. The DHCP server will be enabled and the LAN interface
will be given an IP address of 10.10.10.1.
Page 199 / 210
61200361L1-1E
© 2002 ADTRAN, Inc.
199
VIEWING THE DHCP INFO TABLE
Introduction
The NetVanta 2000 series supports three IP addressing schemes on the WAN interface -- dynamic, static,
and PPP over Ethernet (PPPoE). When the WAN interface is configured for dynamic (DHCP) or PPPoE
addressing, important information can be obtained by viewing the DHCP information the NetVanta 2000
series receives from your provider’s DHCP server. The NetVanta 2000 series contains a table listing all
DHCP information for both the LAN and WAN interfaces. This DLP discusses viewing that information.
Prerequisite Procedures
This DLP assumes the NetVanta 2000 series is connected to a PC and a browser session is active. Refer to
DLP-001 for more details.
Tools and Materials Required
No special tools or materials required.
To prevent electrical shock, do not install equipment in a wet location or during a
lightning storm.
Page 200 / 210
Section 5, DLP-022
NetVanta 2000 Series System Manual
200
© 2002 ADTRAN, Inc.
61200361L1-1E
DLP-022
Perform Steps Below in the Order Listed
1.
Log in to the NetVanta 2000 series as
admin
(see DLP-001 for details).
2.
From the main menu (located across the top of the screen) select
C
ONFIG
.

Rate

4 / 5 based on 1 vote.

Popular Adtran Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top