TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router

Chapter 3: Basic Installation

15

Configuring PC in Windows NT4.0

1.

Go to

Start / Settings / Control Panel

. In the

Control

Panel, double-click

Network

and choose the

Protocols

tab.

2.

Select

TCP/IP Protocol

and click

Properties

. (

See Figure

3.12)

3.

Select the

Obtain an IP address from a DHCP server

radio

button and click

OK

. (

See Figure 3.13)

Figure 3.12: TCP / IP

Figure 3.13: IP Address

TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router

Chapter 3: Basic Installation

16

Factory Default Settings

Before configuring your, you need to know the following default settings.

Web Interface (Username and Password)

Username: admin

Password: admin

The default username and password are “

admin

” and “

admin

” respectively.

LAN Device IP Settings

IP Address: 192.168.0.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site

RFC-1483 Bridged IP LLC

DHCP server

DHCP server is enabled.

Start IP Address: 192.168.0.100

IP pool counts: 100

LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory.

The default values are shown below.

LAN Port

WAN Port

IP address

192.168.0.254

Subnet Mask

255.255.255.0

DHCP server function

Enabled

IP addresses for

distribution to PCs

100 IP addresses continuing from

192.168.0.100 through 192.168.0.199

The RFC-1483 Bridged IP LLC

function

is

enabled

to

automatically get the WAN IP

address from the ISP.

Attention

If you ever forget the username/password to login to the router, you may

press the RESET button up to 6 seconds to restore the factory default

settings.

Caution

: After pressing the RESET button for more than 6 seconds, to be sure you power

cycle the device again.

Attention

TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router

Chapter 3: Basic Installation

17

Information from your ISP

Before configuring this device, you have to check with your ISP (Internet Service Provider) to find out

what kind of service is provided such as DHCP (Obtain an IP Address Automatically, Static IP (Fixed IP

Address) and PPPoE.

Gather the information as illustrated in the following table and keep it for reference.

PPPoE

VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name,

and Domain Name System (DNS) IP address (it ca be automatically assigned

by your ISP when you connect or be set manually).

PPPoE

/

PPPoE

with Pass-through

VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name,

and Domain Name System (DNS) IP address (it ca be automatically assigned

by your ISP when you connect or be set manually).

In addition, additional

WAN address can be assigned using PPPoE dialer.

PPPoA

VPI/VCI, VC / LLC-based multiplexing, Username, Password and Domain

Name System (DNS) IP address (it ca be automatically assigned by your ISP

when you connect or be set manually).

RFC 1483 Bridged

VPI/VCI, VC / LLC-based multiplexing to use Bridged Mode.

RFC 1483 Routed

VPI/VCI, VC / LLC-based multiplexing, IP address, Subnet mask, Gateway

address, and Domain Name System (DNS) IP address (it is a fixed IP

address).

TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router

Chapter 3: Basic Installation

18

Configuring with your Web Browser

Open your web browser, enter the IP address of your router, which by default is

192.168.0.254

, and click

“

Go

”, a user name and password window prompt will appear.

The default username and password

are “admin” and “admin”. (See Figure 3.14).

Figure 3.14: User name & Password Prompt Widonw

Congratulation! You are now successfully logon to the Router!

TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router

Chapter 4:Configuration

19

Chapter 4: Configuration

At the configuration homepage, the left navigation pane where bookmarks are provided links you directly

to the desired setup page, including:

Status

-

ARP Table

-

Wireless Association

-

Routing Table

-

DHCP Table

-

PPTP Status

-

Email Status

-

Event Log

-

Error Log

-

NAT Sessions

-

Diagnostic

-

UPnP Portmap

Quick Start

Configuration

-

LAN

-

WAN

-

System

-

Firewall

-

VPN

-

QoS

-

Virtual Server

-

Time Schedule

-

Advanced

Save Config to FLASH

Language

(provides user interface in Finnish and English languages)

Logout