1. Home
    2. /
  2. Manuals
    3. /
  3. Repotec
    4. /
  4. RP-IP2105
    5. /
  5. 4
Page 16 / 42 Scroll up to view Page 11 - 15
4-Port Cable/DSL Broadband Router Use’s Guide
Extended menu
Submenu
Function
Figure 4-2
4.1 Status
When finish configuring the WAN/LAN Setup, the Status screen will list up the
connection status for the Broadband Routers' WAN/LAN interfaces, firmware version
numbers.
16
Page 17 / 42
4-Port Cable/DSL Broadband Router Use’s Guide
Figure 4-3
4.1.1 Statistics
View the statistics of packets sent and received on WAN interface.
Figure 4-4
z
Refresh.
Update data monitor table to display newest data.
4.2 WAN Setup
Users can setup the Internet connection mode for their local area network on this
17
Page 18 / 42
4-Port Cable/DSL Broadband Router Use’s Guide
page. Router provides four types of connection modes: Dynamic IP (obtain an IP
automatically), PPPoE User (ADSL), Static IP User and PPTP. These types are
listed in the screen for the Internet Connection Type setting of the WAN Setup
section. Users can choose the corresponding connection mode according to their
situation. The default setting for Router is Dynamic IP.
Figure 4-5
When finished making your changes on this screen, click the Save button to save
these changes.
4.2.1 For Dynamic IP Setting
z
Select “Dynamic IP User” button.
z
You can check the “Physical Address Clone” checkbox to copy the MAC
Address of your PC to be the MAC address of this device.
z
The MTU feature specifies the largest packet size permitted for network
transmission. Enter the value desired, for most Router users, it is recommended
to use1496. By default, MTU is set at1496.
z
Primary DNS and Secondary DNS, DNS (Domain Name System) Server IP
must be filled up when the ISP Provider provide these information to you, if the
ISP Provider provides Dynamic IP Address, then you can skip on these dialog
18
Page 19 / 42
4-Port Cable/DSL Broadband Router Use’s Guide
box.
z
Click “Apply” button then finish of setting.
Figure 4-6
NOTE:
Some ISPs may require you to register the MAC address of your card/adapter .So
It is recommended that the PC registered with the ISP is used to setup the MAC
Address Clone.
When finished making your changes on this screen, click the Save button to save
these changes.
4.2.2 For PPPoE Setting
z
Select “PPPoE User (ADSL)” button.
z
PPPoE Account and PPPoE Password, Enter the User Name and Password
provided by your ISP.
z
You can check the “Physical Address Clone” checkbox button to copy the MAC
Address of your PC to be the MAC address of this device.
z
The MTU feature specifies the largest packet size permitted for network
transmission. Enter the value desired, for most DSL users, it is recommended to
use1492. By default, MTU is set at 1410.
z
Primary DNS and Secondary DNS, DNS (Domain Name System) Server IP
must be filled up when the ISP Provider provide these information to you, if the
ISP Provider provides Dynamic IP Address, then you can skip on these dialog
box.
z
Auto disconnect when idle. You can configure the Router to cut your connection
with your ISP after a specified period of time (Max Idle Time). If you have been
disconnected due to inactivity, Connect to Internet manually, It enables the
19
Page 20 / 42
4-Port Cable/DSL Broadband Router Use’s Guide
Router to automatically re-establish your connection as soon as you attempt to
access the Internet again. If you wish to activate Connect on Demand, click the
“Connect” button. If you want your Internet connection to remain on at all times,
You can check the Connect to Internet automatically checkbox. The default
setting for Router is Connect to Internet automatically.
z
Click “Apply” button then finish of setting.
Figure 4-7
When finished making your changes on this screen, click the Save button to save
these changes.
4.2.3 For Static IP Setting
z
Input the IP Address sub mask ,Primary DNS , Secondary
DNS and Gateway
provided by your ISP.
z
You can check the “Physical Address Clone” checkbox button to copy the MAC
Address of your PC to be the MAC address of this device.
z
The MTU feature specifies the largest packet size permitted for network
transmission. Enter the value desired, for most Router users, it is recommended
to use1496. By default, MTU is set at 1496 Primary DNS and Secondary DNS, If
your ISP provided at least one DNS Server IP Address, type that IP Address in
the Primary DNS address fields. You can type up to another DNS Server IP
Addresses. The Router will utilize these for quicker access to functioning DNS
Servers.
z
Click “Apply” button then finish of setting.
20

Rate

3.3 / 5 based on 3 votes.

Popular Repotec Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top