KR.1N

Wireless-N Broadband Router 150Mbps / 1T1R

Chapter 2

：

Getting to know the Router

2.1 Rear Panel and Port Description

Rear Panel Description

Rear Panel

Interface

Description

LAN(1-4)

Connect with your PC’s, Network devices or

uplink to hub or switch.

RESET/WPS

Note: Pressing this button for 7 seconds, the

settings stored will be deleted and restored to

factory default setting. If pressed for 1 second,

WPS (PBC) is enabled.

WAN

Connect with Modem.

POWER

For connecting the Power Adapter

Rear Panel View

6

www.kraun.it

KR.1N

Wireless-N Broadband Router 150Mbps / 1T1R

2.2 Front Panel and LED Description

Refer to the table below for the LED indicators located at the front panel, and their function.

7

www.kraun.it

KR.1N

Wireless-N Broadband Router 150Mbps / 1T1R

2.3 Hardware Installation

Before configuring the Router, please set up your hardware according to the following

diagrams. For better wireless performance, please place the Router in the center of the area

where you would like to have wireless coverage.

1.

Make sure that your Internet

Access Device, such as Cable

Modem, xDSL Modem etc. is

connected correctly and operational.

2.

Connect the Power Adapter to

the POWER interface of the

WIRELESS-N 150Mbps / 1T1R

Router. Use an Ethernet cable

to connect the WAN Interface

of the Router to the Internet

Access Device

CAUTION:

Only use the Power Adapter that came with your Router. Use of other

Power Adapter may damage your Router and will void the Product Warranty.

3.

Use an Ethernet cable to

connect the LAN interface

of the WIRELESS-N ROUTER

150Mbps / 1T1R to the NIC of

the computer.

8

www.kraun.it

KR.1N

Wireless-N Broadband Router 150Mbps / 1T1R

Chapter 3. WEB Management Interface

3.1 Network Configuration of Your Computer

3.1.1 On the desktop of your computer, right-

click “My Network Places”, and then select

“Properties” in the shortcut menu.

3.1.2 In the window that appears, right-click

“Local Area Connection”, and then select

"Properties” in the shortcut menu.

3.1.3 In the pop-up dialog box check “Internet

Protocol (TCP/IP)” and then click “Properties”.

9

www.kraun.it

KR.1N

Wireless-N Broadband Router 150Mbps / 1T1R

3.1.4 In the window that appears, select “Obtain

an IP address automatically (O)” or “Use the

following IP address (S)”.

1) When “Obtain an IP address automatically

(O)” is selected, the window is as shown in the

right figure.

2) Click “Use the following IP address” and enter

details as follows:

IP address: 192.168.0.XXX

(XXX range 2 ~ 254)

Subnet mask: 255.255.255.0

Default gateway: 192.168.0.1

DNS server: Enter the local DNS server address

(for this address, you can consult your ISP) or

the router as the DNS server.

At the end of the setting, click “OK” to submit the

settings. And then click “OK” in the “Local Area

Connection Properties” window.

3.2 Verifying the Connection

3.2.1 If you are unable to access the

Management screen through the browser at

192.168.0.1, select “Start->Programs-

>Accessories->Command Prompt”.

This will open a Command Window. At the

Prompt, enter “Ping 192.168.0.1” and press

Enter. If the system gives the result shown in

the right figure, the connection between your

computer and the router is normal.

10

www.kraun.it