21

Device Information

Model Name

: Displays the model name.

Host Name

: Displays the name of the router.

System Up-Time

: Displays the elapsed time since the device is on.

Date/Time

: Displays the current exact date and time. Sync button is to synchronize the Date/Time with

your PC time without regard to connecting to internet or not.

Software Version

: Firmware version.

LAN IPv4 Address

: Displays the LAN IPv4 address.

LAN IPv6 Address

: Displays the LAN IPv6 address. Default is a Link-Local address, but when

connects to ISP, it will display the Global Address, like above figure.

MAC Address

: Displays the MAC address.

DSL PHY and Driver Version

: Display DSL PHY and Driver version.

Wireless Driver Version

: Displays wireless driver version.

WAN

Line Rate – Upstream (Kbps):

Displays Upstream line Rate in Kbps.

Line Rate – Downstream (Kbps):

Displays Downstream line Rate in Kbps.

Default Gateway/IP4 Address

: Display Default Gateway and the IPv4 address.

Connection Time

: Displays the elapsed time since ADSL connection is up.

Primary DNS Server

: Displays IPV4 address of Primary DNS Server.

Secondary DNS Server

: Displays IPV4 address of Secondary DNS Server.

Default IPv6 Gateway/IPv6 Address

: Display the IPv6 Gateway and the obtained IPv6 address.

WAN

This table displays the information of the WAN connections, users can turn here for WAN connection

information.

Interface

: The WAN connection interface.

Description

: The description of this connection.

Type

: The protocol used by this connection.

Status:

To disconnect or connect the link.

Connection Time

: The WAN connection time since WAN is up.

IPv4 Address

: The WAN IPv4 Address the device obtained.

IPv6 Address

: The WAN IPv6 Address the device obtained.

22

Statistics

LAN

The table shows the statistics of LAN.

Note

: P4 can be configured as EWAN, and when the device is in EWAN profile, there is no P4/EWAN

interface as P4 is working as a WAN port.

(DSL)

(EWAN)

Interface

: List each LAN interface. P1-P4 indicates the four LAN interfaces.

Bytes

: Display the Received and Transmitted traffic statistics in Bytes.

Packets

: Display the Received and Transmitted traffic statistics in Packets.

Errors

: Display the statistics of errors arising in Receiving or Transmitting data.

Drops

: Display the statistics of drops arising in Receiving or Transmitting data.

Reset:

Press this button to refresh the statistics.

WAN Service

The table shows the statistics of WAN.

23

Interface

: Display the connection interface.

Description

: the description for the connection.

Bytes

: Display the WAN Received and Transmitted traffic statistics in Bytes.

Packets

: Display the WAN Received and Transmitted traffic statistics in Packests.

Errors

: Display the statistics of errors arising in Receiving or Transmitting data.

Drops

: Display the statistics of drops arising in Receiving or Transmitting data.

Reset

: Press this button to refresh the statistics.

xTM

The Statistics-xTM screen displays all the xTM statistics

Port Number

: Shows number of the port for xTM.

In Octets

: Number of received octets over the interface.

Out Octets

: Number of transmitted octets over the interface.

In Packets

: Number of received packets over the interface.

Out Packets

: Number of transmitted packets over the interface.

In OAM Cells

: Number of OAM cells received.

Out OAM Cells

: Number of OAM cells transmitted.

In ASM Cells

: Number of ASM cells received.

Out ASM Cells:

Number of ASM cells transmitted.

In Packet Errors

: Number of received packets with errors.

In Cell Errors

: Number of received cells with errors.

Reset:

Click to reset the statistics.

24

xDSL

Mode

: Modulation protocol, including G.dmt, G.lite, T1.413, ADSL2, AnnexL, ADSL2+ and AnnexM.

Traffic Type

: Transfer mode, here supports ATM and PTM.

Status

: Show the status of DSL link.

Link Power State

: Show link output power state.

Line Coding (Trellis):

Trellis on/off.

25

SNR Margin (dB):

Show the Signal to Noise Ratio (SNR) margin.

Attenuation (dB):

This is estimate of average loop attenuation of signal.

Output Power (dBm):

Show the output power.

Attainable Rate (Kbps):

The sync rate you would obtain.

Rate (Kbps):

Show the downstream and upstream rate in Kbps.

MSGc

(#of bytes in overhead channel message): The number of bytes in overhead channel message.

B

(# of bytes in Mux Data Frame): The number of bytes in Mux Data frame.

M

(# of Mux Data Frames in FEC Data Frame): The number of Mux Data frames in FEC frame.

T

(Mux Data Frames over sync bytes): The number of Mux Data frames over all the sync bytes.

R

(# of check bytes in FEC Data Frame): The number of check bytes in FEC frame.

S

(ratio of FEC over PMD Data Frame length): The ratio of FEC over PMD Data frame length

L

(# of bits in PMD Data Frame): The number of bit in PMD Data frame

D

(interleaver depth): Show the interleaver depth.

Delay

(msec): Show the delay time in msec.

INP

(DMT symbol): Show the DMT symbol.

Super Frames

: The total number of super frames.

Super Frame Errors

: The total number of super frame errors.

RS Words

: Total number of Reed-Solomon code errors.

RS Correctable Errors

: Total number of RS with correctable errors.

RS Uncorrectable Errors

: Total number of RS words with uncorrectable errors.

HEC Errors

: Total number of Header Error Checksum errors.

OCD Errors

: Total number of out-of-cell Delineation errors.

LCD Errors

: Total number of Loss of Cell Delineation.

Total Cells:

Total number of cells.

Data Cells

: Total number of data cells

Bit Errors

: Total number of bit errors.

Total ES

: Total Number of Errored Seconds.

Total SES

: Total Number of Severely Errored Seconds.

Total UAS

: Total Number of Unavailable Seconds.

xDSL BER Test

: Click this button to start a bit Error Rate Test. The ADSL Bit Error Rate (BER) test

determines the quality of the ADSL connection. The test is done by transferring idle cells containing a

known pattern and comparing the received data with this known pattern to check for any errors.

Select the Tested Time (sec), press Start to start test.