Page 26 / 60 Scroll up to view Page 21 - 25
150Mbps Wireless-N AP/ Repeater / Router clientUser Manual
25
Press Apply to complete this operation and close the window.
3.2.
Checking Connection with the Router
After configuring the TCP/IP protocol, use the ping command to verify if the computer
cancommunicate with the Router. To execute the ping command, open the DOS window
andPing the IP address of the 150Mbps Wireless-N AP/ Repeater / Router client
at the DOS
prompt:
For Windows 98/Me: Start -> Run. Type command and click OK.
For Windows 2000/XP: Start -> Run. Type cmd and click OK.
For Windows Vista/7:Start→ Type cmd at the start search bar and press the Enter.
For MAC OS→Thesystem will complete this operation automatically.
At the DOS prompt, type the following command:
If the Command window returns something similar to the following:
C:\Documents and Settings\admin>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Ping statistics for 192.168.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 1ms, Average = 1ms
Then the connection between the router and your computer has been successfully established.
If the computer fails to connect to the router, the Command window will return the following:
C:\Documents and Settings\admin>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Page 27 / 60
150Mbps Wireless-N AP/ Repeater / Router clientUser Manual
26
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Ping statistics for 192.168.1.1:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
Verify your computer's network settings are correct and check the cable connection between the
router and the computer.
In order to make the whole network operate successfully, it is necessary to configure the
150Mbps Wireless-N AP/ Repeater / Router client
through your computer has a WEB
browser installed. Please follow up the steps listed below.
3.3.
Login
Open a web browser (Safari, Internet Explorer, etc.) on the computer you have just
connected to the router, type http://192.168.1.1in the address bar, and press enter
Figure 3-18
After you have logged in, the router's user interface will be displayed. The left menu shows
the main options to configure the system, and the right screen is the summary information for
viewing and adjusting the configurations.
Page 28 / 60
150Mbps Wireless-N AP/ Repeater / Router clientUser Manual
27
Figure 3-19
Page 29 / 60
150Mbps Wireless-N AP/ Repeater / Router clientUser Manual
28
4.
Router Setup
4.1.
Status
This feature provides running status information and detailed information about router.
4.1.1.
Version
Show the hardware version and firmware version.
Figure 4-1
4.1.2.
WAN
This feature provides running status information of the WAN port (the port connect to the
Internet)
Figure 4-2
Connection Type: Display router’s current connection type, It should be one of
“PPPoE”,“DHCP”, “Static IP”, depending on what kind of connection type your ISP
provides.
Physical Address: The physical address of WAN port, this is a unique address assigned by
manufacturer.
IP Address
:
The IP address you obtained after connect to the Internet, if you haven’t
connected to the Internet yet, this field is 0.0.0.0.
Subnet Mask: The Subnet mask you obtained after connect to the Internet, if you haven’t
Page 30 / 60
150Mbps Wireless-N AP/ Repeater / Router clientUser Manual
29
connected to Internet yet, this field is 0.0.0.0.
Default Gateway: The IP address of Default gateway you obtained after connect to the
Internet, if you haven’t connected to Internet yet, this field is 0.0.0.0.
Primary DNS: The DNS server translates domain or website names into IP address, input
the most common DNS server address you used or provided by your ISP.
Secondary DNS: Input IP address of a backup DNS server or you can leave this field blank
Link Status: Show the current status of link information. You can choose connect or
disconnect by manually.
4.1.3.
LAN
This item provides information about router’s LAN port, display LAN port’s physical address,
IP address and current situation of DHCP server.
Figure 4-3
4.1.4.
Wireless
This item provides current running information of wireless.
Figure 4-4
Wireless status: Display wireless interface status is enabled or not
Name (SSID): SSID (Service Set Identifier) is your wireless network's name shared
among all points in a wireless network.
Mode: Current wireless mode of wireless router
Channel
:
Display current channel of your wireless router.
MAC Address
:
The MAC address is used for wireless communication

Rate

4 / 5 based on 1 vote.

Popular Netis Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top