1. Home
    2. /
  2. Manuals
    3. /
  3. NetComm
    4. /
  4. NB5Plus4W
    5. /
  5. 3
Page 11 / 112 Scroll up to view Page 6 - 10
YML754 Rev1
NB5Plus4/W User Guide
www.netcomm.com.au
11
Restoring Factory Defaults
This feature will reset the Modem to its factory default configuration. Occasions may
present themselves where you need to restore the factory defaults on your modem.
Typical situations are:
•
You have lost your username and password and are unable to login to the mo-
dem.
•
You have purchased the modem from someone else and need to reconfigure the
device to work with your ISP.
•
You are asked to perform a factory reset by a member of the NetComm Support
staff.
In order to restore your modem to its factory default settings, please follow these
steps:
•
Ensure that your Modem is powered on (for at least 10 seconds).
•
Use a paper clip or a pencil tip to depress the reset button for ten seconds and
release. At this point, the reset is in progress. Do not power off the unit at this
point.
•
When indicator lights return to steady green, reset is complete. The default set-
tings are now restored. The entire process takes about 45 seconds to complete.
•
Once you have reset the modem to its default settings you will be able to access
the device's configuration web interface using http://192.168.1.1 with username
'admin' and password 'admin'.
Page 12 / 112
NB5Plus4/W User Guide
YML754Rev1
1±
www.netcomm.com.au
Default Settings
LAN (Management)
Field
Setting Details
Static IP Address:
192.168.1.1
*
Subnet Mask:
255.255.255.0
*
Default Gateway:
blank
WAN (Internet)
Field
Setting Details
User Name:
username@isp
Password:
****
Protocol:
PPPoE
VPI:
8
*
VCI:
35
*
IP Address:
192.168.1.1
*
Subnet Mask:
255.255.255.0
*
Default Gateway:
0.0.0.0
*
Modem Access
Field
Setting Details
User Name:
admin
Password:
admin
*
Default Setting.
Although in most cases you will not be required to alter
these default settings for your NB5Plus4/W, your ISP may identify specific
settings to enable connection to their service.
Please refer to your ISP or
Network Administrator for further information.
Page 13 / 112
YML754 Rev1
NB5Plus4/W User Guide
www.netcomm.com.au
1²
Connecting your NB5Plus4/W
The NB5Plus4/W can be connected via a USB cable or an Ethernet cable or both. The USB
connection is simply an ethernet simulation.
As far as your computer is concerned the
USB connection is an Ethernet connection, hence DHCP and other protocols will work the
same as for Ethernet.
To connect to your ADSL Router, you need to have either an Ethernet Port or a USB
Port present on your Computer/Notebook.
Connecting your NB5Plus4/W ADSL Modem via
ETHERNET
1. Connect your NB5Plus4/W to either a computer directly or a network hub or
switch using CAT5 ethernet cables.
2. Connect the power pack to the ADSL Modem and switch on the power switch.
3. Ensure that there is a LAN link light on the NB5Plus4/W.
4. Ensure that the computer you intend to use has an IP address in the same
subnet as the NB5Plus4/W ADSL Modem.
(e.g. the NB5Plus4/W’s default IP is
192.168.1.1 - your computer should be on 192.168.1.100 or similar.)
If you
have DHCP enabled on your computer, the NB5Plus4/W will assign your com-
puter a suitable IP address.
5. Ensure that your computer has a LAN link light.
6. Connect one end of the ADSL phone line
to the NB5Plus4/W ADSL Modem and
the other end to the wall socket.
Page 14 / 112
NB5Plus4/W User Guide
YML754Rev1
14
www.netcomm.com.au
Connecting your NB5Plus4/W ADSL Modem via
USB
1. Connect the power pack to the NB5Plus4/W ADSL Modem and switch on the
power switch.
2. Connect your NB5Plus4/W to a computer directly via USB cable.
3. When the computer is booted, the Add New Hardware Wizard will launch and
prompt you to provide a driver for your NB5Plus4/W ADSL Modem.
Insert the
CD provided.
4. Follow the on-screen prompts to load the driver.
Refer to the section below for
more detailed information.
(You may need to restart your computer).
5. Connect one end of the ADSL phone line
to the NB5Plus4/W ADSL Modem and
the other end to the wall socket.
Installing the USB driver (Windows 98/Me/2000/XP only)
When you install the USB driver on your computer it creates a Virtual Ethernet
Adapter, which can be configured in the same way as a Network Interface card with
DHCP or static IP address. To install the USB driver please follow the steps below:
1. Boot your machine into Windows 98/Me/2000/XP.
2. Insert your NetComm NB5Plus4/W CD into your CD-ROM drive.
3. Plug power up to your NB5Plus4/W and switch ON.
4. Plug a USB cable from the back of the unit into a spare USB socket on your com-
puter.
5. The Windows “Add New Hardware Wizard” should appear.
Click Next to con-
tinue.
6. Ensure the option “Search for the best driver….” is chosen and click Next.
7. Choose “Specify location”, untick any other boxes and click on the Browse but-
ton.
Open the CD-ROM drive location of your NetComm NB5Plus4/W CD and
then select the ‘USBdriver’ folder. The USB driver will be installed.
Page 15 / 112
YML754 Rev1
NB5Plus4/W User Guide
www.netcomm.com.au
15
NB5Plus4W Antenna Instructions
Before continuing with the Hardware installation, you may need to connect the
Antenna
1. The antenna has a retaining nut which must be screwed into the SMA connector
on the back of the modem.
Place the screw retaining nut over the antenna con-
nection on the rear of the NB5Plus4W and turn it clockwise.
Note:
Do not over-tighten the attaching nut - but do make sure that you have
screwed it all the way to its end.
2. Bend the antenna to a 90
o
angle.
Note:
Please note that you may have to rotate the complete antenna assembly to
do this and have the antenna pointing vertically.
Screw retaining
nut clockwise
over the antenna
connection
Bend antenna
to a 90
o
angle

Rate

4.5 / 5 based on 2 votes.

Popular NetComm Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top